ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Funtana 90 cock up
6 posts
 
   3DBatix Forum Index -> Workshop
 
Author Message
Batix Kid



Joined: 07 Apr 2005
Posts: 90

PostPosted: Thu Feb 02, 2006 2:41 pm    Post subject: Funtana 90 cock up  

I just got my new funtana 90,i got around to fixing the elevator into place (my dad measured and marked it by the way) it was a very snug fit so we thought that cyano would be best,applied it then slid elevators into the correct place, gave it five mins or so,measured it once again but the little bugger was about 3mm bigger one side.My dad measured it wrong mad

Will this effect the way the plane fly's?
Back to top  
fly boy 1



Joined: 12 Nov 2004
Posts: 286
Location: Milwaukee,WI

PostPosted: Thu Feb 02, 2006 5:13 pm    Post subject:  

It should be fine. What I would worry about is that you used CA on the elevator. I would use epoxy 5 or 30 minutes are fine, I used 5 min. As long as the alignment is close it should be ok. My elevators were way off on throws, and It still flew fine. I'd be worried about the ca bond on the elevator though, it is a pretty high stress area, and ca is a bit brittle. It should be ok as long as you do a good job on the carbon supports.
Eric

_________________
Team Greenfield News and Hobby

Dave Partick 27% Extra 330L
Raptor 50
TOC1 30% Yak 54
Judge 540
Shocky Extra

http://www.greenfieldnewsandhobby.com
Back to top  
Lafus Maximus



Joined: 23 Oct 2005
Posts: 3

PostPosted: Thu Feb 02, 2006 8:00 pm    Post subject:  

CA is fine for gluing in the horizontal stab, actually better penetration into the balsa then epoxy. I used thin CA on my funtana 90's horizontal stab and have 150+ flights on it, still fine.
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1178
Location: Sunnyvale, CA

PostPosted: Thu Feb 02, 2006 8:52 pm    Post subject:  

O youre talking about the horizontal stab! I get it now...if its that minute of a different, you wont really notice it. I would agree that the CA will probably be ok. I did that on my Funtana 40 and it stood up to full throttle blenders and what not. Didnt stand up to cartwheeling down the runway though Razz
_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
xtraflyr



Joined: 10 Sep 2005
Posts: 28
Location: Chester NJ

PostPosted: Fri Feb 03, 2006 3:04 pm    Post subject:  

Actually on my QQ Yak he recommends using thin ca,then you put a bead of mid or slow where the fuse and the stab meet,then I hit it with some accelerator.. It's been holding up awesome for the 100s of flights I have on it.. I do some hard Blenders also with it and its fine..

Later,

_________________
REAL PLANES HAVE A ROUND COWL AND a MONOWING!!!

1/3 Lanier Laser200,Brison 4.2 JR 8103, Hitecs

QQ YAK OS160 JR 8103, Hitecs

Midwest Cap 80" DA50 JR 8103,Hitecs

Funtana 90s YS 120sf, JR 9303 PCM,Hitecs
Back to top  
fly boy 1



Joined: 12 Nov 2004
Posts: 286
Location: Milwaukee,WI

PostPosted: Fri Feb 03, 2006 4:10 pm    Post subject:  

Well I guess the thin CA will be ok there.
_________________
Team Greenfield News and Hobby

Dave Partick 27% Extra 330L
Raptor 50
TOC1 30% Yak 54
Judge 540
Shocky Extra

http://www.greenfieldnewsandhobby.com
Back to top  
 
   3DBatix Forum Index -> Workshop All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive