ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Need help, Bunch of questions!
17 posts
 
   3DBatix Forum Index -> Gear Talk
 
Author Message
Joedaniwhite



Joined: 15 Jan 2005
Posts: 44
Location: Millbury, MA

PostPosted: Sat Oct 29, 2005 1:44 pm    Post subject: Need help, Bunch of questions!  

Hi guys!

I'm putting together my first gasser. It's a Pacific models Edge 540 27% with a Fuji 50EI engine. (don't laugh, it's all I could afford) The engine mount holes are 1/4" diameter and the bolts I'm using are metric but pretty close to 3/16" I want to find some rubber isolation mounts to use. Any suggestions? I checked all the most popular sites but they don't give specific info on them to feel comfortable ordering them up. I could make them if I have to...

#2) Are most of you guys running the choke via servo? Seems like it would be worth the weight.

#3) Someone mentioned an optical kill switch. Is this necessary or is the common $7 kill switch set up sufficient. If optical is the way to go, where do you find them?

#4) Running all the servo power through the receiver should be sufficient for this size airplane correct? The servo's may have about 100"oz of torque.

#5) Is 6 volt the way to go or is 4.8 sufficient?

I think that is all I have for now! Thanks for the help! No one around here has a gasser that I can look at for correct set up so I have to rely on what I read and any help you guys can give me.

Thanks,

Joe

_________________
The dumb thumb King!
Back to top  
3D-kid330



Joined: 14 Nov 2004
Posts: 391
Location: Fremont, CA

PostPosted: Sat Oct 29, 2005 2:15 pm    Post subject:  

I don't know all of them, but here goes.

3: You don't have to run one, but it is probably a nice thing to have saftey-wise.

4: Running all servo power through the RX will be fine. That's how most people do it. You may want to think about a bit higher torque than 100 oz. in.; you will probably be feeling blowback especially on the rudder. More torque never hurts. Razz

5: You could run a 4.8, but IMO it's better to run 6 volts as long as your servos are rated for it.You could even use Li-Ion batteries-which are lighter and therefore have a greater capacity to weight ratio-to keep the weight down and you will be able to fly MUCH longer before charging. Li-Ions can be found at various places including here: www.DuraliteBatteries.com

I run their batts in most of my planes and have no problems, and their service can't be beat. One reason I prefer them is that they have Cell Balancers built in and a reverse protected charge lead; just a bit of extra insurance.

Li-Ions are just my preferance, but go with whatever "floats your boat."

Brandon

Brandon

_________________
Lower??!!
Back to top  
craigman



Joined: 31 May 2004
Posts: 105
Location: Redding, CA

PostPosted: Sat Oct 29, 2005 2:52 pm    Post subject:  

Joe,
congrats on your first gasser! The 27%'ers are good ones to start with. Cheap (for a gasser), and simple.

As far as a choke servo, i personally like using them. For two reasons, it aids in starting the motor, and can be used to kill the motor. Which is good incase you have throttle servo failure in the air. Not quite good as having a optical kill switch, but works very well. As for a choke servo, i'm just using a standard Hitech servo in my Wildhare 35%. But i would advise in getting a decent throttle servo. Something metal geared.

Running everything through the Rx is just fine. Even a lot of people do it in 35%'ers. Just be sure to run a heavy duty on/off switch from your battery.

As far as a battery, i would run 6v. It makes the servos stronger and quicker. Something around the 2000mah or bigger should give you some pretty good flight times.

With the Fuji and Edge combo you have, i'm guessing you'll be doing a lot of sport flying with some mild 3D'ing. So as far as servos, 100oz's of torque or better would be a good choice. They don't have to be digitals, but digitals are always a good choice if you can afford them. But not needed in your case with only 1 servo per controll surface.

Good luck with you new project! And if you have any questions, feel free to shoot me an email or p.m.

Craig
Back to top  
Joedaniwhite



Joined: 15 Jan 2005
Posts: 44
Location: Millbury, MA

PostPosted: Sat Oct 29, 2005 6:56 pm    Post subject: Thanks Guys!  

Thank you for the advice. I'm hoping to get into some good 3D. I'm hoping the 50cc size airplane will be a big enough step up from my UCD 60 and Funtana. Those don't harrier well along with some other manuvers.

I watched some videos of the 50cc's flying and I could tell the pilots were clearly working harder than the 40% class but they did seem to handle all the 3D stuff.

I just hope I didn't make a mistake by not waiting and going even larger?

If I truly love the gasser, I'll sell everything else and get one more!

Wish me luck!

PS: The weather has sucked so bad here in the north east in October! Makes it hard to keep one in the air which to me blows away any Sim time. But hey, what can you do? Sim flying is better than nothing?

Keep-em-up guys!!!!!!

_________________
The dumb thumb King!
Back to top  
Joedaniwhite



Joined: 15 Jan 2005
Posts: 44
Location: Millbury, MA

PostPosted: Sun Oct 30, 2005 4:25 pm    Post subject: Was the Pacific model a good choice?  

Was the plane I chose a decent choice for 3D? Your comment above said mostly sport and some mild 3D. I'm hoping this darn thing will do it all???

What's your thoughts?

Joe

_________________
The dumb thumb King!
Back to top  
craigman



Joined: 31 May 2004
Posts: 105
Location: Redding, CA

PostPosted: Sun Oct 30, 2005 5:43 pm    Post subject:  

Joe,
yes the Edge should 3D pretty well. But with the Fuji, it won't be a hover monster. Those are big heavy engines. For serious 3d'ing, you'll need something like a 3W60 or a DA 50. The Fuji is probably AT LEAST a pound or two more than the DA or W, and not near the same hp. That's why i just assumed you were going to "sport" fly it. My mistake.
IMO, 50cc class planes aren't real 3D machines anyways. The wing loading is pretty high on them. Yes they'll do all the tricks, but not a good and gracefull as the 35%'ers and bigger. But the 50cc class is a great place to start for sure. A lot cheaper and more simple. And also, a lot easier to transport.

Any more questions, just shoot them my way! Also, give us the specs on that plane.

Good luck and post some pics of you new bird!
Back to top  
Joedaniwhite



Joined: 15 Jan 2005
Posts: 44
Location: Millbury, MA

PostPosted: Mon Oct 31, 2005 4:44 pm    Post subject: Some specs for ya!  

Here is the 27% Edge by Pacific Models. It says that the engine range is 35 to 42cc's and to go with the upper end for 3D. I built many of my own airplanes and assembled many ARF's and I'd say that this ARF was well done. It has Du-bro hardware but I'm replacing most of it... It has a really neat feature. The engine box slides in and out of the airframe. Once you get your engine set up, you slide the box out to get the correct cowl spacing then remove the engine from the box and epoxy the box into the fuselage. Kinda cool!

The wing span is actually 84.5" and the plane is supposed to weigh in around 14.5 pounds when done. It has airfoil control surfaces. I think the wing loading is around 29oz/ft

I went with the Fuji for money reasons mostly?? My fear was spending too much money on a 50cc class airplane and not seeing enough difference in performance without going BIGGER!! I looked at the weight and the DA with mount and stuff (no muffler) came in at 3.13lb The Fuji was 3.5 (No muffler) so it is a 1/2 pound heavier at any rate.

The new Fuji 50EI is rated at 5.2hp at 10,000 (don't believe I'll be turning that rpm though) The DA was rated at 5hp but it didn't list at what RPM. I bought the Fuji brand new muffler and all for $399 (3 year warranty) The DA was $600 not including the muffler. Believe me, the DA is the way to go from here on if I like the gassers! The Fuji will make a great second engine!

I'll send a video of this thing in the air soon! Here's a pic of the thing coming along.

Joe



27% Edge & Eng 001.jpg
 Description:
 Filesize:  146.13 KB
 Viewed:  274 Time(s)

27% Edge & Eng 001.jpg



_________________
The dumb thumb King!
Back to top  
craigman



Joined: 31 May 2004
Posts: 105
Location: Redding, CA

PostPosted: Mon Oct 31, 2005 5:32 pm    Post subject:  

Looks good Joe!
Did you ever decide on what electronics your going to use?
Back to top  
Joedaniwhite



Joined: 15 Jan 2005
Posts: 44
Location: Millbury, MA

PostPosted: Mon Oct 31, 2005 5:59 pm    Post subject: radio equip  

I'm putting in a Futaba 138dp pcm receiver and I found some JR MG servos that have a 150"oz torque rating. I think that'll do for this thing?? I did go with a MG throttle servo too and a 6 volt RX pack.

Boy, the first gasser hurts huh? I'm already $1200 deep not including radio. I know that's not even an engine's worth on the bigger ones though. eek Someday I'll have a freakin monster!

Joe

_________________
The dumb thumb King!
Back to top  
Joedaniwhite



Joined: 15 Jan 2005
Posts: 44
Location: Millbury, MA

PostPosted: Mon Oct 31, 2005 6:01 pm    Post subject: Forgot to tell ya!  

Made those clamps holding it up myself with my mig welder.

They work pissa! Fully adjustable!

_________________
The dumb thumb King!
Back to top  
craigman



Joined: 31 May 2004
Posts: 105
Location: Redding, CA

PostPosted: Mon Oct 31, 2005 6:16 pm    Post subject:  

150oz's of torque will be just fine!
Ya,, these things can get expensive real quick. I'm into my 35%'er for around $3500! And figure another 1K to start for a 40%'er! YIKES!

Glad to hear you went 6 volt. It will make your servos stronger and faster. Sounds like your going to have on hell of a nice plane!

Waiting for some maiden video!
Back to top  
Joedaniwhite



Joined: 15 Jan 2005
Posts: 44
Location: Millbury, MA

PostPosted: Thu Nov 03, 2005 12:52 pm    Post subject: Fuel tank  

Craigman!

I want to put my fuel tank at the CG, under the wing tube. What's your thoughts on this?

The engine has a diaphram type pump but it will be a long distance to the carb to suck fuel for the first start. Also, the tank will be lower than the carb. Shouldn't be a problem with a pump on the engine right?

If I go just in front of the wing tube, I can do anything I want with the tank. 18oz is almost one pound though. It would suck having it forward in the fuselage. Plane would fly like crap at first with an extra pound up front, yes?

Any advice on this?

Joe

_________________
The dumb thumb King!
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Thu Nov 03, 2005 2:08 pm    Post subject:  

the carb is able to pump fuel from that far away, you will just need to prime it for about 20 flips to get gas to it. also, if you choose to put the tank IN FRONT of the wing tube..
1. it really wouldnt make a difference with distance the carb will need to pull gas from.
2. your CG would be changing constantly, so you would have different flying characteristics at different tank levels.
either way will work fine though.

my $0.02

_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
Joedaniwhite



Joined: 15 Jan 2005
Posts: 44
Location: Millbury, MA

PostPosted: Thu Nov 03, 2005 2:48 pm    Post subject: Fuel tank  

Thanks Butthead! Very Happy

I'll give it a shot at the cg which is pretty much under the wing tube.

Can't wait to get this thing in the air!

Joe

_________________
The dumb thumb King!
Back to top  
craigman



Joined: 31 May 2004
Posts: 105
Location: Redding, CA

PostPosted: Thu Nov 03, 2005 6:28 pm    Post subject:  

Joe,
i'm with Butthead. Put your fuel tank on the CG if possible. Your carb will have no problems pulling the fuel that far away. On my Wildhare 35%, mine is roughly 10 inches or so away from the carb. With ignition off, choke on, full throttle, it takes about 7 flips of the prop to get gas to drip out of the carb. Then, choke off, carb at idle, ignition on, three more flips and away i go!
With the Fuji, you have a magneto, so you'll probably go something like,,, choke on, carb at idle, about 7 flips of the prop, will start and run for about 1 second, and then choke off, carb at idle, and then a couple of more flips and your on!
It will take a couple of times to get used to how YOUR engine starts. Every engine is a little different, but that's the basics. Pretty easy stuff.
And you'll really enjoy $2.50 a gallon instead of $15 a gallon for glow fuel!
Have fun dude!
Back to top  
Joedaniwhite



Joined: 15 Jan 2005
Posts: 44
Location: Millbury, MA

PostPosted: Thu Nov 03, 2005 7:06 pm    Post subject: snag!  

Thanks for all the help guys!

I ran into a snag today. Looked like the muffler was going to clear the side cowl and I was only going to cut the bottom. I was wrong. It hit's the side of the cowl and I refuse to cut it and ruin the looks of the plane.

I'm trying to find a slim line, wrap around or Pitts muffler that will fit it. This is the new 50EI engine. They list them for the Fuji 50SA and 50SB. Both have different exhaust dimentions. (Go figure?) So now I need to find out which one will fit and order it up. (delayed another week or so now! DAMN!!!) mad

That's one nice thing about DA. There's nothing they don't make for those things! Oh well, next time!

Joe

_________________
The dumb thumb King!
Back to top  
craigman



Joined: 31 May 2004
Posts: 105
Location: Redding, CA

PostPosted: Thu Nov 03, 2005 9:04 pm    Post subject:  

Joe,,
one thing you might do is go to RCU and to the gas engine section, and do a search for conversion engines or weedeater engines. There are a couple of guys on there that make mufflers for any application if you send them the measurements.
Just a thought!
Later!
Craig
Back to top  
 
   3DBatix Forum Index -> Gear Talk All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive