| |
| Author |
Message |
marekzak

Joined: 16 Feb 2005 Posts: 9 Location: Torun, Poland
|
Posted: Tue Aug 30, 2005 1:45 pm Post subject: Problem with a new SAITO 100? |
|
|
I have a problem with my four-stroke Saito FA-100, I fly U-CAN-DO 3D 60 model.
This is my first engine of this type, so there is no experience what so ever.
The engine is slow, I can get only 8800 rpm on this one, according to my information is suppose to be at least 11000 rpm. I can't get it run higher
than 8k.
So far I burned 3 litters of fuel and couldn't get enough power to fly 3D (Torque).
I use propeller type: APC 16/4W
Fuel mix: 20% oil (synthetic) 12% nitro.
How much nitro do I suppose to use?
Could you help me with this problem?
Any guesses, suggestions, additional questions, please let me know. _________________ Best Regards.
Marek from Poland
http://www.rctorun.pl/
Last edited by marekzak on Tue Aug 30, 2005 1:49 pm; edited 1 time in total |
|
| Back to top |
|
 |
marekzak

Joined: 16 Feb 2005 Posts: 9 Location: Torun, Poland
|
Posted: Tue Aug 30, 2005 1:48 pm Post subject: |
|
|
_________________ Best Regards.
Marek from Poland
http://www.rctorun.pl/ |
|
| Back to top |
|
 |
Butthead

Joined: 08 Oct 2004 Posts: 1054 Location: Belvidere, NJ
|
Posted: Tue Aug 30, 2005 2:35 pm Post subject: |
|
|
well, the saito 100 that i had only turned around 8500rpm with the same prop. i dont think they are made to turn 1100rpm. they would probably cook. _________________ John Paragallo
WildHare RC Extra 330LX 36%/ZDZ 120
Hangar-9 Extra 260 27%/ZDZ 50
Futaba 9C |
|
| Back to top |
|
 |
Shaun

Joined: 10 Sep 2004 Posts: 342 Location: texas
|
Posted: Tue Aug 30, 2005 4:01 pm Post subject: |
|
|
Looking at the chart for the Saito 100, it shows a rpm range of 2000-11,000.
But it's range of propellers is from a 13x9 to a 15x8.
I don't think you'll get 11,000 out of the 16x4. I had a 16x4w on my saito100 and it was a great combo.But I didn't ever get close to 11,000.
http://saito-engines.info/ _________________ http://www.texomarc.org/ |
|
| Back to top |
|
 |
Ramz

Joined: 05 Nov 2004 Posts: 55 Location: New Brunswick, Canada
|
Posted: Tue Aug 30, 2005 4:32 pm Post subject: saito 100 |
|
|
| Try using 15% fuel and a 15x4W prop. That should let it spin up better. I used this combo on my Funtana 40 and it worked great. |
|
| Back to top |
|
 |
3dbatixkid Moderator

Joined: 15 Apr 2004 Posts: 1178 Location: Sunnyvale, CA
|
|
| Back to top |
|
 |
Meyrick Site Admin

Joined: 15 Apr 2004 Posts: 1316 Location: Fremont, CA
|
Posted: Tue Aug 30, 2005 9:33 pm Post subject: |
|
|
I was getting 9200rpms with a 16x4W using 20/20 Powermaster. You need more nitro than 12%. Use at least 20%, 30% is better if you have cash to burn. _________________ --Meyrick-- |
|
| Back to top |
|
 |
3dbatixkid Moderator

Joined: 15 Apr 2004 Posts: 1178 Location: Sunnyvale, CA
|
|
| Back to top |
|
 |
Meyrick Site Admin

Joined: 15 Apr 2004 Posts: 1316 Location: Fremont, CA
|
Posted: Wed Aug 31, 2005 4:50 am Post subject: |
|
|
| 3dbatixkid wrote: | | Meyrick wrote: | | I was getting 9200rpms with a 16x4W using 20/20 Powermaster. You need more nitro than 12%. Use at least 20%, 30% is better if you have cash to burn. |
30% eats up the bearings you dummy The 20/20 seemed to work well. I think that the 15x4W is the best prop as long as it has enough thrust. |
Actually, the 30% is more suitable for the Saito180.  _________________ --Meyrick-- |
|
| Back to top |
|
 |
Swat Cop

Joined: 10 Jun 2004 Posts: 48 Location: Kissimmee, FL
|
Posted: Sat Sep 03, 2005 2:03 pm Post subject: Saito 100 |
|
|
Use 30% Heli fuel, it won't hurt the engine but it will make a LOT more power. Also don't be afraid to lean the engine out especally the low end. It seems most people I see running Saitos have a terrible idle, its because they are too rich. Turn the low speed needle down. As for the high end needle no need to be slobbering rich there either. Its just like any other engine, lean it to the highest RPM then richen just a hair. Little planes like the ones that use a Saito 100 you can hold vertical to make sure you are not too lean.  _________________ http://hometown.aol.com/bike466/index.html
Sunset Flyers St. Cloud, FL
Skyhigh Flyers Orlando, FL |
|
| Back to top |
|
 |
mikey
Joined: 28 Nov 2004 Posts: 109 Location: Greenville, TX
|
Posted: Tue Sep 06, 2005 4:48 pm Post subject: |
|
|
| Thinking about useing 30/23 powermaster on my ys110 has anyone had any problems with doing that? |
|
| Back to top |
|
 |
Swat Cop

Joined: 10 Jun 2004 Posts: 48 Location: Kissimmee, FL
|
Posted: Wed Sep 07, 2005 12:41 pm Post subject: YS 110 |
|
|
I have been using Cool Power 30% Heli in both of my YS 110s with great success. _________________ http://hometown.aol.com/bike466/index.html
Sunset Flyers St. Cloud, FL
Skyhigh Flyers Orlando, FL |
|
| Back to top |
|
 |
mikey
Joined: 28 Nov 2004 Posts: 109 Location: Greenville, TX
|
Posted: Wed Sep 07, 2005 2:01 pm Post subject: |
|
|
How long have you been running the 30%? Have you checked the bearings for wear? Does the motor still tack the same as when it was new? Sorry to ask so many questions just trying to get an idea of how much more stress is put on the motor.
Thanks
Michael |
|
| Back to top |
|
 |
| |