ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Problem with a new YS 110?
14 posts
 
   3DBatix Forum Index -> Gear Talk
 
Author Message
paulaly



Joined: 16 Feb 2005
Posts: 36

PostPosted: Sun Jul 31, 2005 4:10 pm    Post subject: Problem with a new YS 110?  

Hey guys could anybody help with a YS110. My YS is brand new and am running 30% heli fuel and using a 16-6 APC prop on it. I had give the engine 2 tanks on the ground and all seemed to run very good. First flight was good, good transition between idle and power up. Now after 8 flights it is giving me a headache. The last few trips to the field the engine does not want to run good at all. It refuses to idle for any amount of time. I start it up first time everytime. Then I run it at idle then power up then check the speed with my tach. All seems good at this point until it has runs for a few seconds as I take it off the starting bench. I put the thing on the ground go to taxi out and the thing always quits on me.

I can't seem to figure this one out at all. I am not new to engines, I have used them since 93', but this one I just can't get tuned. Please help as it is driving me crazy.

Thanks Paul
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 460
Location: Danville, VA

PostPosted: Sun Jul 31, 2005 6:24 pm    Post subject: Re: Problem with a new YS 110?  

paulaly wrote:
Hey guys could anybody help with a YS110. My YS is brand new and am running 30% heli fuel and using a 16-6 APC prop on it. I had give the engine 2 tanks on the ground and all seemed to run very good. First flight was good, good transition between idle and power up. Now after 8 flights it is giving me a headache. The last few trips to the field the engine does not want to run good at all. It refuses to idle for any amount of time. I start it up first time everytime. Then I run it at idle then power up then check the speed with my tach. All seems good at this point until it has runs for a few seconds as I take it off the starting bench. I put the thing on the ground go to taxi out and the thing always quits on me.

I can't seem to figure this one out at all. I am not new to engines, I have used them since 93', but this one I just can't get tuned. Please help as it is driving me crazy.

Thanks Paul


Paul, have you checked the valve settings now since you have been running it. YS engines are very sensative to tuning. If the top end is good, then we need to set the bottom end. What is the RPM on the ground at idle. Since you say it won't idle, what exactly is it doing. If it is slowing down and quiting, your low end is rich and the low end screw needs to be turn out some to let more air in since it is an airbleed screw. If the engine speeds up at idle, then it is lean and the screw needs to be turned in. This turns should be done in 1/8-1/4 turns.

Before you touch anything, what plug are you running also? My YS engines will start to act up on idle and all they normally need is a new plug. Only use a YS plug or a OS "F" glow plug on these. Try to only use synthetic oil also with these engines.

If that is the problem, then we can try to tackle it from another angle.

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
ryan



Joined: 13 Dec 2004
Posts: 147
Location: North Carolina

PostPosted: Sun Jul 31, 2005 7:00 pm    Post subject:  

You shouldn't be going through alot of glow plugs with YS's. I know of several flyers (albeit pattern flyers) that go out and fly alot and have had plugs last them for entire seasons. I don't fly mine THAT much, but I haven't had to replace it in a hundred or so flights.

Have you messed with the regulator? Set that flush, and if all else fails, go back to factory settings and start over.

The 1.10 is a great engine, as are all of the YS line. They are just a little different and it takes a while to become acclimated to them. If you are near someone that flies them alot, try asking them to look at your setup and such. Good luck with it! I hope you get your problems sorted out.

_________________
Ryan
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 460
Location: Danville, VA

PostPosted: Sun Jul 31, 2005 7:24 pm    Post subject:  

ryan wrote:
You shouldn't be going through alot of glow plugs with YS's. I know of several flyers (albeit pattern flyers) that go out and fly alot and have had plugs last them for entire seasons. I don't fly mine THAT much, but I haven't had to replace it in a hundred or so flights.

Have you messed with the regulator? Set that flush, and if all else fails, go back to factory settings and start over.

The 1.10 is a great engine, as are all of the YS line. They are just a little different and it takes a while to become acclimated to them. If you are near someone that flies them alot, try asking them to look at your setup and such. Good luck with it! I hope you get your problems sorted out.


Good point Ryan. I mentioned the glow plug due to it being a new engine and he may have been running it rich and may have fowled it out in a short period of time. I normally get most of the flying season from one plug before it needs to be changed. When it wants a new plug, it will let you know.

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
paulaly



Joined: 16 Feb 2005
Posts: 36

PostPosted: Mon Aug 01, 2005 3:09 pm    Post subject:  

Thanks for the reply guys. The top end is good at 9500rpm, but the bottom end starts at 2400-2500rpm then slowly drops to a stop. I have tried to set the low end needle valve but no joy. I have actually just got back from the field, I left early due to this problem. Another guy has a used YS 110 on his bird and I noticed that he has alot more commpression than mine, quite a bit more. When I looked into this I can tun over the engine with my little finger. His runs absolutely perfect top bottom end is just cool. I started with an OS F plug but changed it to a YS plug today thinking it would help but no. My way of thinking is that the commpression is not enough to pump the fuel in the bottom end. Hmmm! not sure what to think. Like I said this is straight out of the box new at $500can. A good engine I know but it is hard to justify buying this if the engine doesn't work.
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 460
Location: Danville, VA

PostPosted: Mon Aug 01, 2005 6:52 pm    Post subject:  

paulaly wrote:
Thanks for the reply guys. The top end is good at 9500rpm, but the bottom end starts at 2400-2500rpm then slowly drops to a stop.


That is a classic sign of being too rich. You should lean the bottom end out slightly.

paulaly wrote:
I have tried to set the low end needle valve but no joy. I have actually just got back from the field, I left early due to this problem. Another guy has a used YS 110 on his bird and I noticed that he has alot more commpression than mine, quite a bit more. When I looked into this I can tun over the engine with my little finger. His runs absolutely perfect top bottom end is just cool.


My YS .91FZ does the same thing and makes you think the compression is gone, but once you fire it up, it is strong as an OX. My YS 1.10FZ has done the same thing and still runs great. My buds Saito 150 does the same thing also.

paulaly wrote:
I started with an OS F plug but changed it to a YS plug today thinking it would help but no. My way of thinking is that the commpression is not enough to pump the fuel in the bottom end. Hmmm! not sure what to think. Like I said this is straight out of the box new at $500can. A good engine I know but it is hard to justify buying this if the engine doesn't work.


OS "F" or YS plug will work fine. I think your problem is your low end adjustment. Lean the low end screw roughly 1/8 turn by turning it out slightly. Need to let more air in. I had to adjust my regulator slightly also. Maybe 1/8 - 1/4 turn out also.

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
paulaly



Joined: 16 Feb 2005
Posts: 36

PostPosted: Tue Aug 02, 2005 12:01 pm    Post subject:  

So the commpression can feel weak but it will still perform the same. I ask this because this is the first time in 12 yrs that I have seen this happen. Will this alqways feel weak or will I feel the commpression again. I'm going to try what you said to see if I can get this thing to work

Thanks
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 460
Location: Danville, VA

PostPosted: Tue Aug 02, 2005 1:57 pm    Post subject:  

paulaly wrote:
So the commpression can feel weak but it will still perform the same. I ask this because this is the first time in 12 yrs that I have seen this happen. Will this alqways feel weak or will I feel the commpression again. I'm going to try what you said to see if I can get this thing to work

Thanks


I know it is weird, but it has happen to me before. I thought I had problems with compression also, but it still performed flawlessly. I first noticed that on my YS .91FZ first, but it will still hover a 8lbs bird and spin a APC 15x6 with no problem. I have compression with it off now, but it was strange. My YS 1.10FZ did the same thing, but it didn't freak me out this time when it happened.

You should feel compression again after it is ran.

Your engine should be able to hold an idle for atleast 20-30 secs with very little change in RPM. You probably will see the rpm changing some, but it should stay around the same RPM. Example, if it is holding around 2300, it may go 2320, 2330, 2300, 2310, 2300, 2320, etc... It probably won't be a steady 2300, but as long as it is holding around the same RPM it should be good. You should be able to let the engine idle on it's own without it dying. If it speeds up, it is lean and if it slows down, it is rich. You want to find the sweet spot that will let it run almost steady with little flucuation.

The engine should drop down to idle almost instantly from TOP END, not 3500, 2800, 2550, 2420, 2330, 2300. It should go roughtly 9500 to 2300 almost instantly, but it may stair step down slightly, but not much. If it doesn't transition smoothly, then your regulator needs to be adjusted slightly, but leave it flush for right now until you get the low end set.

Keep us informed.

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
paulaly



Joined: 16 Feb 2005
Posts: 36

PostPosted: Wed Aug 03, 2005 12:47 pm    Post subject:  

Well I have gone back to when it came out of the box now. I've noticed that my tappet clearence was alot more than what it should have been. So now I have reset it to what the book says and I will go from there. I'll let you now how I get on
Back to top  
Colin



Joined: 08 Jun 2004
Posts: 25
Location: Canada

PostPosted: Thu Aug 04, 2005 2:18 pm    Post subject:  

Quote:
It refuses to idle for any amount of time. I start it up first time everytime. Then I run it at idle then power up then check the speed with my tach. All seems good at this point until it has runs for a few seconds as I take it off the starting bench. I put the thing on the ground go to taxi out and the thing always quits on me.


My YS.91 heli engine did this for a while and I couldn't figure it out. Turns out there was dirt in the diaphram and it would not stop pumping fuel at idle causing the engine to go super rich (flood) and die. After it was cleaned out it worked perfect!

Colin

_________________
Great Hobbies
Thunder Tiger
Morgan Fuels
HobbyCraft Canada
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 460
Location: Danville, VA

PostPosted: Thu Aug 04, 2005 2:25 pm    Post subject:  

Colin wrote:
Quote:
It refuses to idle for any amount of time. I start it up first time everytime. Then I run it at idle then power up then check the speed with my tach. All seems good at this point until it has runs for a few seconds as I take it off the starting bench. I put the thing on the ground go to taxi out and the thing always quits on me.


My YS.91 heli engine did this for a while and I couldn't figure it out. Turns out there was dirt in the diaphram and it would not stop pumping fuel at idle causing the engine to go super rich (flood) and die. After it was cleaned out it worked perfect!

Colin


Colin, that is a great point. I had a piece of grass to do that to me on my .91FZ. After it was cleared it ran great. Definately something to check.

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
N81U



Joined: 09 Aug 2004
Posts: 136
Location: Goodyear AZ

PostPosted: Sat Aug 06, 2005 7:07 pm    Post subject:  

Remember to check the fuel tank the clunk may be stuck in the front of the tank, also check for leaks, with all that pressure you can get leaks.
The compression will go away if the throttle barrel is completely closed.


Lee

_________________
www.LeeUlingerModels.com
Back to top  
paulaly



Joined: 16 Feb 2005
Posts: 36

PostPosted: Sun Aug 07, 2005 5:01 pm    Post subject:  

So after I had gone to basics and reset the tappets the commpression was all of a sudden back to normal. I think that the locking nuts was just not tightened up at the factory because the gap was quite consderable. Hey thanks for all the help on this one. I took it to the field today after doing all this and waiting for time and good weather the engine needed a little tuning and now seems to work just fine. The transition is good and it now idels with no problems. This is a site I know I can get alot of very useful info and help at. Thanks Paul
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 460
Location: Danville, VA

PostPosted: Sun Aug 07, 2005 6:27 pm    Post subject:  

paulaly wrote:
So after I had gone to basics and reset the tappets the commpression was all of a sudden back to normal. I think that the locking nuts was just not tightened up at the factory because the gap was quite consderable. Hey thanks for all the help on this one. I took it to the field today after doing all this and waiting for time and good weather the engine needed a little tuning and now seems to work just fine. The transition is good and it now idels with no problems. This is a site I know I can get alot of very useful info and help at. Thanks Paul


Glad to help and have fun with the plane.

big grin

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
 
   3DBatix Forum Index -> Gear Talk All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive