ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

epp foam
11 posts
 
   3DBatix Forum Index -> Foamies
 
Author Message
thefasttrack



Joined: 09 Apr 2005
Posts: 80
Location: miami

PostPosted: Sat Jul 16, 2005 4:26 pm    Post subject: epp foam  

if i boaght epp foam in 6mm sheets will it hold up as good as depron or will it not be a strong like flexx wise
Back to top  
JR.Master



Joined: 07 Nov 2004
Posts: 462
Location: San Angelo

PostPosted: Sat Jul 16, 2005 7:48 pm    Post subject:  

i'd personally say sepron will be a whole lot more forgiving. Very Happy
_________________
Did I do that? Hummmmmm!Yep, sure did!
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 454
Location: Jackson, MS

PostPosted: Wed Aug 03, 2005 8:41 pm    Post subject: Re: epp foam  

thefasttrack wrote:
if i boaght epp foam in 6mm sheets will it hold up as good as depron or will it not be a strong like flexx wise


The Tuff flight 4D lite is made from epp foam. They flew it into a tree. Flipped it over and threw it back in the air. $65 is a little step, but it you can do that to it, it may be worth it. Who knows, I may just get one and put my Diablo 3D stuff on it.

Video --> http://www.tufflight.com/4d_lite1.wmv

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
thefasttrack



Joined: 09 Apr 2005
Posts: 80
Location: miami

PostPosted: Thu Aug 04, 2005 4:27 pm    Post subject:  

wat about actaully making one into a diablo i wounder how that would work out
Back to top  
mikey



Joined: 28 Nov 2004
Posts: 102
Location: Greenville, TX

PostPosted: Thu Aug 04, 2005 6:43 pm    Post subject:  

I am doing a diablo out of fan fold has anyone done one before. Not sure how it will work but it is cheap. It will cost about three dollars to do the plane and they sell it at lowes. It looks like it will work.
Back to top  
thefasttrack



Joined: 09 Apr 2005
Posts: 80
Location: miami

PostPosted: Fri Aug 05, 2005 1:52 pm    Post subject:  

wats fan fold
Back to top  
Radioflyer



Joined: 14 Sep 2004
Posts: 325
Location: Kalamazoo, MI

PostPosted: Fri Aug 05, 2005 6:06 pm    Post subject:  

I'm impressed with the EPP foam. That Tuff Flight is awesome Very Happy
_________________
God bless us all, and keep us safe.


www.bryanhusk.com/jay
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 454
Location: Jackson, MS

PostPosted: Fri Aug 05, 2005 6:40 pm    Post subject:  

Radioflyer wrote:
I'm impressed with the EPP foam. That Tuff Flight is awesome Very Happy


I've decided to get one of those ugly @$$ planes because it is so tough. Looks aren't everything.

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
mikey



Joined: 28 Nov 2004
Posts: 102
Location: Greenville, TX

PostPosted: Sat Aug 06, 2005 3:38 pm    Post subject:  

Fan Fold is 6mm depron with a plastic tape coating on each side this makes it heaver and stronger. Fan fold foam is more ridged. Not sure how much more it weighs I just cut out a diablo the foam pieces weigh 3.75 ounces. Does anyone know the weight of the diablo with standard depron and not any equipment and hardware. Lowes sells 25 sheets 24"x48" for 37 dollars with tax. You can only get blue one side has writing on it. Fan fold is located in the insulation department.
Back to top  
thefasttrack



Joined: 09 Apr 2005
Posts: 80
Location: miami

PostPosted: Sat Aug 06, 2005 5:33 pm    Post subject:  

but wat about 6mm epp faom wit it work or not
Back to top  
rhelfrich



Joined: 22 Dec 2004
Posts: 4

PostPosted: Mon Aug 15, 2005 8:18 pm    Post subject:  

Fan Flold from Lowe's in Gilroy, CA is Light blue Expanded Poly Styrene. I just checked i have 1.5 bundles in the garage. I built 2 Foame 3D's and 2 75%(of plan size) diablo's out of FFF.

On Diablo's, I extend the wing span out to 37" with 37" Carbon fiber spar. Diablo,s horizontal fusalge will break rear main wing joint and at the front of the Horizontal Stab. I assemble with Low Temp hot Glue. I use a GWS 350 D on 12x6, 11x8 and 10x6 props, CC20P, 2S1P 720 &900mAh. Motor up and GWS stick on the bottom of the Horiz fusepiece. Widen the horiz fusealage before the horizontal stabilizer. Then and a bead of low temp hot glue top and bottom in the break prone areas. I have 88 flights on the last one flying in a plowed field. The tail surfaces tend to stall before the wings, so the elevator (throws about 30degrees) needs more throw or enlargement. I have glued on the nose three times.

On The Foame3d were near stall with 350dand 12x6 with 2s1p2100mah. 3D's tended to split the fusealge along the carbon fiber rod on hard landings.

i use hot glue because it seems to be more flexable than CA and the Carbon fiber rods are more reusable than with CA.
Needless to say I have 1.5 years in rc planes and 4month in 3d stuff.
Back to top  
 
   3DBatix Forum Index -> Foamies All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive