ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Another new foamy!
28 posts
 
   3DBatix Forum Index -> Foamies
 
Author Message
fly boy 1



Joined: 12 Nov 2004
Posts: 286
Location: Milwaukee,WI

PostPosted: Sun May 29, 2005 8:19 pm    Post subject: Another new foamy!  

Well, my beloved diablo exploded in flight, so i picked up a new plane and motor. My choice was the Quique Somenzini Yak 54 that he flew in the 2004 E-TOC. For the motor, i got the new park 400 outrunner, since the setcrew on the himax stripped. I got it done in about 2.5 hours total, which is pretty good for me . This motor seems to pull as hard as my trusty old himax 2812-840, matbe a little bit less. I am currently using a 12-3.8 apc sf prop, but they reccomend a 11-4.7, so I'll see how this works out. Tonite i pulled it out on the street, and i have to say, it donut's as nice as Zak's funtana 40 did in the video ( Can you tell I like the new smilies lol). The all up weight is about 13.5 onces. Quique seems to have designed the same way we have the X brace fusealage, but it looks much nicer, and it also doesn't twist as much. This thing should knife edge like a biotch, because it has a crapload of side area. So far I think it'll be a real winner. I've seen one of these fly indoors, and it is very smooth, like a pattern type plane. Well, I'll have a flight test tomorrow as well as some pics in flight. I hope it goes well!
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Mon May 30, 2005 4:47 am    Post subject:  

hahaa.. i knew you were gonna go out and get one of those.
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
fly boy 1



Joined: 12 Nov 2004
Posts: 286
Location: Milwaukee,WI

PostPosted: Mon May 30, 2005 7:26 am    Post subject:  

Butthead wrote:
hahaa.. i knew you were gonna go out and get one of those.

Well, I couldn't resist. This motor seems to be pretty goo too, I'll let you guys know once I fly it how good it really is.it will hover aroundhalf throttle, and the vertical should be good.

And of course I had to take those yucky JR stickers off laughing .
Back to top  
john wondra



Joined: 05 May 2004
Posts: 360
Location: auburn, wa

PostPosted: Mon May 30, 2005 12:44 pm    Post subject:  

[quote="fly boy 1"]
Butthead wrote:


And of course I had to take those yucky JR stickers off laughing .


good man

_________________
John Wondra RAMS VP
Team 3D Foamy/3D Foamy Suport
__________________________
www.3dfoamy.com
www.northwest3d.com
www.e-flightline.com
www.Falconbatteries.com
www.cutimages.com <all your custom vinyl needs>
Back to top  
3D-kid330



Joined: 14 Nov 2004
Posts: 391
Location: Fremont, CA

PostPosted: Mon May 30, 2005 6:49 pm    Post subject:  

Bad man. JR RULES big grin
_________________
Lower??!!
Back to top  
ryan



Joined: 13 Dec 2004
Posts: 147
Location: North Carolina

PostPosted: Mon May 30, 2005 7:11 pm    Post subject:  

I just picked one of those up the other day. I wanna see if I can persuade QQ to give me the stuff to make a Byp-Yak. That would be off the scale badass.
_________________
Ryan
Back to top  
john wondra



Joined: 05 May 2004
Posts: 360
Location: auburn, wa

PostPosted: Mon May 30, 2005 7:56 pm    Post subject:  

good luck with that... Confused
_________________
John Wondra RAMS VP
Team 3D Foamy/3D Foamy Suport
__________________________
www.3dfoamy.com
www.northwest3d.com
www.e-flightline.com
www.Falconbatteries.com
www.cutimages.com <all your custom vinyl needs>
Back to top  
3D-kid330



Joined: 14 Nov 2004
Posts: 391
Location: Fremont, CA

PostPosted: Mon May 30, 2005 8:00 pm    Post subject:  

Hey John, are you going to make the DOD Fly in?
_________________
Lower??!!
Back to top  
ryan



Joined: 13 Dec 2004
Posts: 147
Location: North Carolina

PostPosted: Mon May 30, 2005 8:38 pm    Post subject:  

john wondra wrote:
good luck with that... Confused


What is that in reference to? Getting the stuff or the plane itself?

_________________
Ryan
Back to top  
fly boy 1



Joined: 12 Nov 2004
Posts: 286
Location: Milwaukee,WI

PostPosted: Tue May 31, 2005 12:11 pm    Post subject:  

Well, guys, the plane flew great, for the 10 seconds it was in the air. frown It went up with reversed ailerons. Any advice to people with this plane, or one's looking at it, they are fragile as hell. It went in with the motor off, and completely destroyed the fuse in front of the wing. My fault tho, so I'm not knocking the plane at all. Oh well, no more foamies ever, too much bad luck with them.
Back to top  
ryan



Joined: 13 Dec 2004
Posts: 147
Location: North Carolina

PostPosted: Tue May 31, 2005 12:27 pm    Post subject:  

Naaaahhh...

Don't give up! Glue that thing back together. The third time's a charm. I had a little trouble when I first started flying foamys, but after you get used to them they are alot of fun.

_________________
Ryan
Back to top  
slowracing



Joined: 18 Apr 2005
Posts: 26
Location: Williamsburg, VA

PostPosted: Wed Jun 01, 2005 6:07 pm    Post subject:  

fly boy 1 wrote:
Well, guys, the plane flew great, for the 10 seconds it was in the air. frown It went up with reversed ailerons. Any advice to people with this plane, or one's looking at it, they are fragile as hell. It went in with the motor off, and completely destroyed the fuse in front of the wing. My fault tho, so I'm not knocking the plane at all. Oh well, no more foamies ever, too much bad luck with them.


I have a Hobby Lobby Yak 55 that has taken more hard hits than soft landing.

Here's the damage list:

Flight 1: It cart wheeled during a very winding landing attempt. The entire aft section of the plane broke off, only the control rods kept it together...fixed it.
Flight 2: Everything was going well until I hit the only light pole within a mile of me. It broke the wing in half upon impact of the pole (also not the battery off) then went out of control nose first in the pavement. Crushed everything in front of the wing...fixed it.
Flight 3: Lost control of it in the sun and landed at half throttle at about a 45deg angle. Another broken motor mount, ripped out the landing gear (I had added that morning) broke the bottom of the fuselage in many pieces…fixed it.
Flight 4-6: Pretty much uneventful, a few hard landings, with little to no crumpled up foam.

What’s my point you’re asking by now…a little time, foam safe CA and maybe some balsa here and there and your flying again…just fix it
big grin

_________________
www.sloweracing.com
www.octaneonline.com
Back to top  
fly boy 1



Joined: 12 Nov 2004
Posts: 286
Location: Milwaukee,WI

PostPosted: Wed Jun 01, 2005 6:48 pm    Post subject:  

Thanks for the kind words guys. I don't think that I'm gonna repair it, because when I repaired my diablo for the first time, the repair failed in flight, which is why i bought the yak. I don't really want another foamy anymore, I just have VERY bad luck with them . I'm kinda discouraged from them now, so now i've got the gear to sell. I just don't really know how to repair this stuff, i only started last summer, so I need more experience I guess. Oh well, I can use the funds from that to help pay for my big Yak-54.
Back to top  
ryan



Joined: 13 Dec 2004
Posts: 147
Location: North Carolina

PostPosted: Wed Jun 01, 2005 9:05 pm    Post subject:  

fly boy 1 wrote:
I just don't really know how to repair this stuff, i only started last summer, so I need more experience I guess. Oh well, I can use the funds from that to help pay for my big Yak-54.


How are you going to get experience if you give up? Give it a whirl, then you can say you tried. Make the repair nice and clean so that it is strong. I've used hot glue, epoxy (not so much with those two since they are pretty heavy), fiber reinforced packing tape, and of course foam safe CA to fix my junk before.

I'm actually working on mine now, I haven't had the time to work on anything in the past few days. I really doubt it can be that bad of a break. You should see Quique's prototype Byp-Yak, that is if he hasn't trashed it yet. That thing is about twice as heavy as his newer ones just from glue from repairs. I dunno if it gives you any confidence to know that a multiple world champ has an airplane that he basically disintigrated or not, but it is sorta funny nonetheless. cool

_________________
Ryan
Back to top  
N81U



Joined: 09 Aug 2004
Posts: 135
Location: Goodyear AZ

PostPosted: Wed Jun 01, 2005 9:14 pm    Post subject:  

If you are new to R/C do not give up on foamies they are your best chance at getting experience. It’s not just the flying it is also good practice for preflight checking with out allot of $$$$$$$$ tied up. What would you do if you crashed your big Yak because of reversed servo? You might quit entirely, now we can’t have that. Just keep at it and I do suggest a foamie that is made of 6mm Depron, they are easy to fix and harder to break. Keep at it

Lee
big grin
Back to top  
FarNorth3DFlier



Joined: 02 Jun 2005
Posts: 7
Location: North Pole, Alaska

PostPosted: Thu Jun 02, 2005 8:52 am    Post subject:  

Do not give up. I'm new to 3D foamies and there is a learning curve to everything new, I have Been flying other type planes for 27 years and one thing I learned DO NOT LET IT GET TO YOU or you will not enjoy this GREAT HOBBY no matter what type of plane you fly. I have fixed planes that were jigsaw puzzles, so start now, the more you repair the better you are. My first foamy 2 weeks ago I used my ultimate as a lawn dart, pulling out of hoover motor stops. broke both wings off, my antena pulled out of receiver and broke up the front real nice. Jumped in and fixed everything including receiver in 2 hours and changed my speed controll (FMA super 20 NOT GOOD) Make sure every plane no matter what type double and triple check radio installation this is a must do and you will solve many uoooops did I do that. IMO gorilla glue is great for foam been using this type of glue for years, light strong and foams up to 3 times amount applied (Great For Repairs also) just watch it and clean off excess with rubbing alcohol every 5 minutes. Sorry for the long winded 2cents Latter, Dan
Back to top  
fly boy 1



Joined: 12 Nov 2004
Posts: 286
Location: Milwaukee,WI

PostPosted: Thu Jun 02, 2005 12:05 pm    Post subject:  

Well, so far I have found that 6mm depron is the way to go for foamies. The 2mm stuff is just not worth it . I might get another one if i don't have to scratch build it again. The only other thing at my lhs is an insane foamies extrra 300, but the foam seems kind of junky. Maybe if i got sponsored or something, but I dought that will happen. It's like $150 every time i get a new one, but I have hs-56 servo's now, and they are the shizzle so maybe.
Back to top  
3D-kid330



Joined: 14 Nov 2004
Posts: 391
Location: Fremont, CA

PostPosted: Thu Jun 02, 2005 9:52 pm    Post subject:  

If you do scratch build one again, maybe it would be possible for you to use laminate construction like there is at www.3DFoamy.com . A lot stronger, but the same weight. kind of like comparing the strength of a thin sheet of wood (traditional) to the strength of plywood (the laminate construction).

Or it you dont want to scratch build, you cant beat the price or the quality of the 3DF's, IMO.

I know what you mean about them being fragile. My friend Kyle caught mine after a demonstration when the batt was real low and even though he caught it gently, the tail feathers folded. Even EPP is not as strong as the laminate. That stuff flakes everywhere.

I will only purchase the 3DF planes for that reason and many others big grin

Just my $0.02 Razz

_________________
Lower??!!
Back to top  
FarNorth3DFlier



Joined: 02 Jun 2005
Posts: 7
Location: North Pole, Alaska

PostPosted: Thu Jun 02, 2005 9:55 pm    Post subject:  

If you have not been flying some type of other 3D plane before foamies break in easy to the 3D foamies, just like when you first started flying rc planes you probably didn't train on a pitts special or a mustang to learn. I always use the KISS method when venturing into new areas of this great hobby with great success if you do this you will be flying rc planes for many more years without all the frustration. Stay away from the high end products, brushless motors ect for a few months. Use a flat plate 6mm fuse with a carbon fiber rod with no x brace for easier fixes. This is my 12 year olds sons set up for first 3D foamie plane. GWS 350 D geared motor, most beginners will more than not break the brushless before wear it out. 11.1v E-tech 1250 mah Battery, pixie 20 SC, works great will hover a 15oz plane. last week he burned a motor up and bent a prop shaft to gearbox and broke a wing tip all on different flights the cost $ 4.50 in parts and a little gorilla glue and remember speed management all the time, GL, Dan
Back to top  
FarNorth3DFlier



Joined: 02 Jun 2005
Posts: 7
Location: North Pole, Alaska

PostPosted: Thu Jun 02, 2005 10:41 pm    Post subject: Is 3DFoamy still selling planes  

I heard last week about 3DFoamy selling buisness last week and are giving refunds for advanced plane and other orders?
Back to top  
fly boy 1



Joined: 12 Nov 2004
Posts: 286
Location: Milwaukee,WI

PostPosted: Fri Jun 03, 2005 3:46 am    Post subject:  

Ok guys, maybe I should have rephrased this, I don't have a lot of experience in doing repairs.depron just seems to lose it's structural integrity.Anyway, I might build another if I want to some other time.
Back to top  
3D-kid330



Joined: 14 Nov 2004
Posts: 391
Location: Fremont, CA

PostPosted: Fri Jun 03, 2005 3:58 pm    Post subject:  

Levi sold the buisiness to his friend John who will be taking care of the manufacturing and packaging, while Levi will still handle designing the planes. The reason for this is that it was hard to keep up with thousands of emails a day, so since the business grew so big, it was better for them to do both separately.

As for the refunds, according to his site (www.3DFoamy.com), he refunded the orders that he couldn't ship out before the move until John gets things running again, when kits will be able to be produced.

Just had to clear it up. smile

Brandon

_________________
Lower??!!
Back to top  
Radioflyer



Joined: 14 Sep 2004
Posts: 339
Location: Kalamazoo, MI

PostPosted: Fri Jun 03, 2005 7:01 pm    Post subject:  

There is hardly any structural integrity to depron.That's why there is many carbon rods in them I cracked my Tensor in half when falling out of a hover a foot off the ground. I thought it hit really lightly too Shocked I fixed it in two minutes by putting a balsa bandaid on it,and a alittle foam safe CA. Worked like a champ. Don't give this up, it is the cheapest way to become great at 3D. Since flying my Tensor(13 flights) I am hovering my Funtana .40 much more stablily and confidently than ever Very Happy
_________________
God bless us all, and keep us safe.


www.bryanhusk.com/jay
Back to top  
slowracing



Joined: 18 Apr 2005
Posts: 26
Location: Williamsburg, VA

PostPosted: Sun Jun 05, 2005 4:19 am    Post subject:  

fly boy 1 wrote:
Ok guys, maybe I should have rephrased this, I don't have a lot of experience in doing repairs.depron just seems to lose it's structural integrity.Anyway, I might build another if I want to some other time.


Okay my horror story continues...

I’m not sure I even want to admit this but…I went flying just a few minutes ago and made a major mistake, I forgot to extend my transmitter antenna eek I did my ground check as usual; everything checked out and all control surfaces were moving in the correct direction. Maybe my mistake was doing it so close, within a few feet. I took off fine and then got into trouble at about the 50-100 foot mark. The plane went crazy and didn’t respond to any inputs especially the throttle back input. Well it took a nose dive into the asphalt. Here are a couple pix of the damage. I will also post repair pictures. They might help lead the way to your repairs. I’ll also mention this is the Yak 55 from Hobby Lobby I only paid $19.99 for it (could be a cheap next plane for ya). It’s been a good plane considering the damage I’ve done to it…it will fly again!!!! Oh, what you can't see if the pictures is the fact that the whole tall section is broke off. The packing tape from the last repair is holding it together laughing



Img_0843.jpg
 Description:
 Filesize:  63.85 KB
 Viewed:  272 Time(s)

Img_0843.jpg



Img_0847.jpg
 Description:
 Filesize:  45.23 KB
 Viewed:  272 Time(s)

Img_0847.jpg



_________________
www.sloweracing.com
www.octaneonline.com
Back to top  
Radioflyer



Joined: 14 Sep 2004
Posts: 339
Location: Kalamazoo, MI

PostPosted: Sun Jun 05, 2005 11:00 am    Post subject:  

OUCH frown
_________________
God bless us all, and keep us safe.


www.bryanhusk.com/jay
Back to top  
fly boy 1



Joined: 12 Nov 2004
Posts: 286
Location: Milwaukee,WI

PostPosted: Sat Jun 11, 2005 3:01 pm    Post subject:  

Ok guys, I wanna build the extra on this site, does anybody here have vodoo powers to keep me from f*****g it up? I was also wondering if I should use, my trusty himax2812-850, E-flite outrunner, or get the new hacker A20-20L?
I would rather use what I have because the hacker will take forever to get here.
I would also like to use some sort of functional landing gear, but I don't know how, so can some one show me how to make carbon fiber gear, like the kind 3d foamy has? Sorry for all the questions guys, I am going to try and get this plane finished in one day.
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Sat Jun 11, 2005 6:23 pm    Post subject:  

fly boy 1 wrote:
Ok guys, I wanna build the extra on this site, does anybody here have vodoo powers to keep me from f*****g it up? I was also wondering if I should use, my trusty himax2812-850, E-flite outrunner, or get the new hacker A20-20L?
I would rather use what I have because the hacker will take forever to get here.
I would also like to use some sort of functional landing gear, but I don't know how, so can some one show me how to make carbon fiber gear, like the kind 3d foamy has? Sorry for all the questions guys, I am going to try and get this plane finished in one day.

1. i dont have voodoo powers
2. use the himax, its about the power of an axi 221234 as i've heard
3. www.darrolcady.com has a REALLY good carbon fiber LG kit

hope this helps!

_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
Chris Cann



Joined: 02 Jun 2005
Posts: 7

PostPosted: Sat Jun 11, 2005 7:01 pm    Post subject:  

Buy the 3dfoamy gear. They have an offer I believe that if it breaks they will give you a new set!
_________________
-Chris-
Fly the best, Fly 3DFOAMY
Back to top  
 
   3DBatix Forum Index -> Foamies All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive