ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Bonding Carbon to Wood
11 posts
 
   3DBatix Forum Index -> Workshop
 
Author Message
Gezoid



Joined: 24 May 2004
Posts: 161
Location: UK

PostPosted: Sun Apr 17, 2005 12:25 am    Post subject: Bonding Carbon to Wood  

Being as my 7C can't mix a pair of elevator servo's properly for my F90 I was thinking of using one elevator servo and joining the two elevator halves. I know wire joiners always flex so thought maybe I could use carbon fibre tube and solid.

I have some carbon push rod tube that's perfect and I figured if I drill it each end for some thinner solid, like on the tail supports, to make a "C" shape I could use this. See pic.

So what do you use to bond carbon to itself and to the wood?



Image1.gif
 Description:
 Filesize:  14.61 KB
 Viewed:  339 Time(s)

Image1.gif



_________________
Ya torkin' ta me?
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 460
Location: Danville, VA

PostPosted: Sun Apr 17, 2005 5:24 am    Post subject:  

I'm sure gorilla glue would bond them together securely. That is what I used to install robart hinges on my FT90, but thats plastic to wood, but I don't think it matters with Gorilla Glue.

You can find it for about $4 at Home Depot for the small bottle in the US, but since you are in the UK I can't help there. Buy it online. You wouldn't need much. Read the directions, then go for it.

Works great and is very strong, but takes a while to fully cure but that is very minor for the holding power of the stuff. It will nearly anything to anything.

http://www.gorillaglue.com



IMG_2561.JPG
 Description:
 Filesize:  99 KB
 Viewed:  330 Time(s)

IMG_2561.JPG



_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
JR.Master



Joined: 07 Nov 2004
Posts: 462
Location: San Angelo

PostPosted: Sun Apr 17, 2005 8:22 am    Post subject:  

Use epoxy glue about 2 ton strength big grin
_________________
Did I do that? Hummmmmm!Yep, sure did!
Back to top  
ryan



Joined: 13 Dec 2004
Posts: 147
Location: North Carolina

PostPosted: Sun Apr 17, 2005 5:38 pm    Post subject: Re: Bonding Carbon to Wood  

Gezoid wrote:
Being as my 7C can't mix a pair of elevator servo's properly for my F90 I was thinking of using one elevator servo and joining the two elevator halves. I know wire joiners always flex so thought maybe I could use carbon fibre tube and solid.

I have some carbon push rod tube that's perfect and I figured if I drill it each end for some thinner solid, like on the tail supports, to make a "C" shape I could use this. See pic.

So what do you use to bond carbon to itself and to the wood?


I say epoxy and microballoons or milled cotton. Rough it up good and glue it. Have you thought about maybe using a CF "blade" (for lack of better wording) as the two horizontals that will glue into the elevator? By that I mean a slab of CF, I would think that would be easier to work with and wouldn't split when you drill it.

I don't have any experience with Gorilla Glue, but if i remember correctly it's polyurethane. Is that right Derrick? If so, I'm not sure about its use with a CF to CF bond. CF to wood would be fine though.

_________________
Ryan
Back to top  
Gezoid



Joined: 24 May 2004
Posts: 161
Location: UK

PostPosted: Mon Apr 18, 2005 12:41 pm    Post subject:  

In the end I used 30min epoxy which worked good. The joiner is pretty tough and weighs nothing but still isn't twist proof enough for the F90. I've got an F40 to build later, maybe I'll use it on that.

Ended up making one out of 6 swg piano wire. That mutha aint bendin' baby! Gotta skin over where its in the elevator halves with 1/32nd ply. Tough as old boots! It weighs about 3/4 ounce, so about half the weight of the second elevator servo I would have used. Sorted. sly wink

_________________
Ya torkin' ta me?
Back to top  
Chris



Joined: 16 Apr 2004
Posts: 367
Location: Canada

PostPosted: Mon Apr 18, 2005 1:15 pm    Post subject:  

why not use a y harness
_________________
-Chris-
3D Foamy
Back to top  
Gezoid



Joined: 24 May 2004
Posts: 161
Location: UK

PostPosted: Mon Apr 18, 2005 1:23 pm    Post subject:  

Mainly cos one servo has to be reversed and you need some way to adjust end points etc. I know there's a thing called an Equaliser but I couldn't get one over here in the UK - and anyway I've got this spare 9151 doing nothing and ya know what it's like when ya get a idea in your head... laughing
_________________
Ya torkin' ta me?
Back to top  
JR.Master



Joined: 07 Nov 2004
Posts: 462
Location: San Angelo

PostPosted: Mon Apr 18, 2005 2:51 pm    Post subject:  

Do what ryan says man.Don't drill a hole in the carbon are even cut it. just glue it together. Hint if you drill a hole in it you might as well shoot yourself in the foot because then its structule integraty decreases. Weak and very brittle laughing
_________________
Did I do that? Hummmmmm!Yep, sure did!
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 460
Location: Danville, VA

PostPosted: Mon Apr 18, 2005 4:26 pm    Post subject: Re: Bonding Carbon to Wood  

ryan wrote:
I don't have any experience with Gorilla Glue, but if i remember correctly it's polyurethane. Is that right Derrick? If so, I'm not sure about its use with a CF to CF bond. CF to wood would be fine though.


Yes, it is a Poly glue. I have never used it for CF to CF but for CF to wood is great. I used it when installing the CF support rod on the back of the FT90 which is CF to wood. It bonds to glass, plastics, ceramics, metal, stone and more so I think CF to CF would work. It won’t become brittle over time, and it’s 100% waterproof, so it won’t contract or expand with temperature or humidity changes. Another nice thing is that it foams up a bit when you apply it, so a little bit goes a long way and you don't need to spread it around so much. When I put my Robart hinges in, it foamed around the hinge and into the wood pores to secure more, but will not cause damage.

I think if you scuff up the CF first it will attach better. The only downside is it takes longer than epoxy to cure. If you used thin CA to hold it in place then covered with gorilla glue, I think it will hold it with no problem. May have to spray with water to activate the glue since CF won't hold moisture well unless you dip the piece to get it wet.

Let me check with my buddy who makes artifical limbs from CF and glues CF to each other. Let me see what he says since he does this for a living.



IMG_2562.JPG
 Description:
 Filesize:  54.8 KB
 Viewed:  274 Time(s)

IMG_2562.JPG



_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
Jynx13



Joined: 06 Jan 2005
Posts: 45

PostPosted: Mon Apr 18, 2005 6:00 pm    Post subject:  

I am using my 7C on my Fun .90 with no Trouble. All you have to do is is trim in the elevator in the air. It will only trim half but it will fly fine. When you get back on the ground just use sub trim to adjust the other half. It is a little hassle but once you get it that's it. Its easier than joining your elevator halves.
Back to top  
N81U



Joined: 09 Aug 2004
Posts: 136
Location: Goodyear AZ

PostPosted: Mon Apr 18, 2005 10:11 pm    Post subject:  

I would not use carbon tube for that, most carbon is made from strands and will not hold up to twisting and the two holes will compromise it even more. Carbon wrapped tube would be much better and use it as a sleeve for the wire glued in with flash black by NHP.

Lee



P1010007.jpg
 Description:
 Filesize:  43.77 KB
 Viewed:  251 Time(s)

P1010007.jpg



P1010002.jpg
 Description:
 Filesize:  16.52 KB
 Viewed:  251 Time(s)

P1010002.jpg


Back to top  
 
   3DBatix Forum Index -> Workshop All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive