ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Wildhares new 29% Ult..................................
25 posts
 
   3DBatix Forum Index -> Workshop
 
Author Message
JR.Master



Joined: 07 Nov 2004
Posts: 462
Location: San Angelo

PostPosted: Tue Apr 05, 2005 5:36 pm    Post subject: Wildhares new 29% Ult..................................  

check this out guys. this is all copied from the site i hope you like it.

* Wingspan 64 inches.
* Wing area 1450 sq. in.
* Length 70 inches spinner to tail
* Weight: approximately 17 lbs min.

Wild Hare R/C is proud to announce the newest addition to our line of 50-70cc airplanes, the 29% Ultimate biplane. Patterned after the original Ultimate 10-300 designed by Gordon price, this plane is designed for the intermediate ARF builder and for the intermediate to expert R/C pilot.

The Ultimate is intended to provide excellent aerobatic and 3D flight performance with economical 50cc class gasoline engines. It was flight tested with a Desert Aircraft DA-50R, but it’s designed with enough room to accept engines up to 75cc. The production plane with the DA-50 weighs just over 17 lb. Plenty of wing area means that this is a biplane that is easy to fly and land, no bad habits.

This Ultimate model is designed to be simple to assemble and disassemble at the field. The wing struts are attached by 4-40 socket head screws into blind nuts, the wings attach to the cabanes with 2 4-40 screws and nuts, and the lower wing attaches with two screws. The wings are one piece, so no spar is required nor are flying wires on the wings needed. Installation of the wings typically takes no more than 5 minutes.

The size of this plane also means it will fit into most pickup trucks and full size vans without disassembly which makes the plane extremely convenient.
The Ultimate is happy with pretty much any good 50cc range engine such as a DA-50, BME-50, Brison 3.2, etc. The generous wing area allows heavier engines too such as G62, 3w 60, Fuji 64, etc. The plane is designed for maximum flexibility. It is set up to balance with a DA-50 with pull-pull rudder or with a G62 with all servos in the tail.

Though this is a high performance aircraft this plane is gentle to fly and land. It has very stable flight characteristics, and it lands as gracefully as it flies. Like any bipe the extra drag requires a little power on landing but other than that it’s like any of our other planes.

As with other Wild Hare ARFs, this plane is 95% complete when you get it. The wings are built-up and covered in Ultracote, all the wood is laser cut, and attention to little details like tank mounting and landing gear attachment make the plane very easy to assemble. It’s designed to be light, but not at the expense of strength for the everyday pilot. Aircraft ply and epoxy firewall and gear mounts. Tab/slot construction, all this says the plane is not just for the pro’s. It’s covered in Ultracoat/Oracover and is easily repaired. The pre-mounted cowl makes setting up the engine a snap.
This is the perfect 2nd plane for the gasoline engine user. And for those of you with a G62, here's another Wild Hare plane that will give your engine a happy home.

The new Ultimate is supplied with painted landing gear and a very nice tailwheel assembly and Robart style pin hinges. No other hardware is supplied with the kit since many people have their own ideas about hardware. Wild Hare does have available a hardware accessory pack that includes everything you will need to assemble the plane except glue, spinner, engine, and electronics. The glue is necessary to install the large Robart hinge points.
Features: Built-up wings join to be one piece, single aileron servo per aileron. 6061T6 3/16” Aluminum gear. Fiberglass cowl and wheel pants, painted in urethane enamel. Cowl is pre-mounted, engine thrust angle is built in. Engine and gear mounts are aircraft ply and assembled with epoxy. Hardpoints in ailerons, elevators, and rudder for control horns. Covered with Ultracoat/Oracover. Available in color schemes shown. Wood parts are laser cut for accurate assembly. Robart type hinge holes pre-drilled. Tank mount and radio tray pre-installed. Radio is accessed through the fuse bottom with lower wing removed and there is generous open work room. Easy field assembly/teardown.



ultimate-001-top.jpg
 Description:
 Filesize:  71 KB
 Viewed:  570 Time(s)

ultimate-001-top.jpg



_________________
Did I do that? Hummmmmm!Yep, sure did!
Back to top  
JR.Master



Joined: 07 Nov 2004
Posts: 462
Location: San Angelo

PostPosted: Tue Apr 05, 2005 5:38 pm    Post subject:  

another view


ultimate 004a.jpg
 Description:
 Filesize:  32.83 KB
 Viewed:  568 Time(s)

ultimate 004a.jpg



_________________
Did I do that? Hummmmmm!Yep, sure did!
Back to top  
JR.Master



Joined: 07 Nov 2004
Posts: 462
Location: San Angelo

PostPosted: Tue Apr 05, 2005 5:38 pm    Post subject:  

another view


ultimate 005a.jpg
 Description:
 Filesize:  34.85 KB
 Viewed:  567 Time(s)

ultimate 005a.jpg



_________________
Did I do that? Hummmmmm!Yep, sure did!
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Tue Apr 05, 2005 6:46 pm    Post subject:  

u coulda just put a link to wildhare's site you know. but ok i guess. looks like a pretty nice plane. good competitor of the AW 27% perhaps..?
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
Chris



Joined: 16 Apr 2004
Posts: 367
Location: Canada

PostPosted: Tue Apr 05, 2005 8:23 pm    Post subject:  

i would get WH over AW anyday
_________________
-Chris-
3D Foamy
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1178
Location: Sunnyvale, CA

PostPosted: Tue Apr 05, 2005 8:31 pm    Post subject:  

You would eh? I would take an AW. Wild hare is good, but they are new. I think they could change the way they build some of their stuff.
_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
Tom Uhlendorf



Joined: 18 Sep 2004
Posts: 563
Location: Morgan Hill, CA

PostPosted: Tue Apr 05, 2005 9:15 pm    Post subject:  

Yeah really. Have you seen a Wild Hare up close? Good design strength wise, and looks. But it seems they have not a care for the weight. There is like quarter inch formers where they should be eighth inch.
And Aeroworks are light, strong, and pretty dang good looking.
Back to top  
Chris



Joined: 16 Apr 2004
Posts: 367
Location: Canada

PostPosted: Wed Apr 06, 2005 3:50 am    Post subject:  

I won't get into any product bashing or product flaming but i have seen a WH or 2 upclose and I have seen AW's the Wildhare just seemed better plus I have seen and heard stuff about AW.
_________________
-Chris-
3D Foamy
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Wed Apr 06, 2005 4:31 am    Post subject:  

Tom Uhlendorf wrote:
Yeah really. Have you seen a Wild Hare up close? Good design strength wise, and looks. But it seems they have not a care for the weight. There is like quarter inch formers where they should be eighth inch.
And Aeroworks are light, strong, and pretty dang good looking.

you're wrong about the weight. my extra weighs 27.5 lbs ready to fly less the prop. that's pretty light for 106" wingspan. but i do agree with zak that aero-works is a more experienced company and wild hare is very new. but tom, the wildhares are built VERY nicely. VERY LIGHT.

_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
JR.Master



Joined: 07 Nov 2004
Posts: 462
Location: San Angelo

PostPosted: Wed Apr 06, 2005 12:00 pm    Post subject:  

Your right wild hare doesn't care about there weight like aeroworks. But i'd take a CA berfore buying one of them anyday. laughing
_________________
Did I do that? Hummmmmm!Yep, sure did!
Back to top  
ryan



Joined: 13 Dec 2004
Posts: 147
Location: North Carolina

PostPosted: Wed Apr 06, 2005 12:02 pm    Post subject:  

As much as I love pink, that is about an ugly ass airplane. Or the scheme anyway. Oh well, to each his own. If Tom likes it and people buy it, go for it. For some reason something about that just doesn't click with me. Specs sound good. I've never seen any WH stuff up close (not that I can remember) but I know AW does have nice airplanes. Especially the kits.
_________________
Ryan
Back to top  
Chris



Joined: 16 Apr 2004
Posts: 367
Location: Canada

PostPosted: Wed Apr 06, 2005 1:45 pm    Post subject:  

with wildhare i believe they offer plain white planes and other schemes aswell for all their planes so hopefully the other ones are better embarrassment
_________________
-Chris-
3D Foamy
Back to top  
JR.Master



Joined: 07 Nov 2004
Posts: 462
Location: San Angelo

PostPosted: Thu Apr 07, 2005 12:39 pm    Post subject:  

Yes dude if I ever bought a pink plane I would strip the pink off fifst and do another scheme .
_________________
Did I do that? Hummmmmm!Yep, sure did!
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Thu Apr 07, 2005 6:45 pm    Post subject:  

JR.Master wrote:
Your right wild hare doesn't care about there weight like aeroworks. But i'd take a CA berfore buying one of them anyday. laughing

you are wayyy wrong. wild hare does care about weight just as much as aero-works. look at the 36% Katana from AW. it's weight is 26-28 lbs. then look at the wild hare 35% Extra 330LX(it's really 36%). the weight is 27-28 lbs. and so far(ready to fly less elevators, stabs are on)my extra is 27 lbs flat. the elevators(and elevators only, as this is all i have left to go on) will only weigh about .5 to .8 lb. that is very light. and just as light as an AW.

_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
Robert300L



Joined: 17 Apr 2004
Posts: 134
Location: San Diego, CA

PostPosted: Fri Apr 15, 2005 7:27 pm    Post subject:  

JR.Master wrote:
Yes dude if I ever bought a pink plane I would strip the pink off fifst and do another scheme . This plane scheme perfectly fits a queer


Are we in 6th grade still?
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Fri Apr 15, 2005 7:34 pm    Post subject:  

Robert300L wrote:
JR.Master wrote:
Yes dude if I ever bought a pink plane I would strip the pink off fifst and do another scheme . This plane scheme perfectly fits a queer


Are we in 6th grade still?

laughing pink is awesome. i wish i could have some of my planes be pink, but i can't cover a plane for CRAP. *thinks about vinyls* hmmmmmm....

_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
JR.Master



Joined: 07 Nov 2004
Posts: 462
Location: San Angelo

PostPosted: Sat Apr 16, 2005 8:09 am    Post subject:  

I can't stand pink for some reason on a plane. I can cover planes with ease, I would take the time to put a new scheme on it. Cool It's all good.
_________________
Did I do that? Hummmmmm!Yep, sure did!
Back to top  
Tom Uhlendorf



Joined: 18 Sep 2004
Posts: 563
Location: Morgan Hill, CA

PostPosted: Sat Apr 16, 2005 9:55 am    Post subject:  

I don't mind the sceme at all. And I'm not "queer" you homophobic. being evil Razz
Back to top  
JR.Master



Joined: 07 Nov 2004
Posts: 462
Location: San Angelo

PostPosted: Sun Apr 17, 2005 8:25 am    Post subject:  

I didn't mean for it to sound like that sorry. Crying or Very sad
_________________
Did I do that? Hummmmmm!Yep, sure did!
Back to top  
Tom Uhlendorf



Joined: 18 Sep 2004
Posts: 563
Location: Morgan Hill, CA

PostPosted: Sun Apr 17, 2005 9:05 am    Post subject:  

Ha, its cool. Cool
Just that I have a few gay friends and I don't really take to kindly to that. I am not gay or anything just that is about as bad as being racist.
Back to top  
Swat Cop



Joined: 10 Jun 2004
Posts: 48
Location: Kissimmee, FL

PostPosted: Sun Apr 17, 2005 12:33 pm    Post subject: Ultimate  

I like the size of that plane but they must have worked hard to make such an ulgy scheme. I predict that will kill a lot of sales for that plane.
_________________
http://hometown.aol.com/bike466/index.html

Sunset Flyers St. Cloud, FL
Skyhigh Flyers Orlando, FL
Back to top  
JR.Master



Joined: 07 Nov 2004
Posts: 462
Location: San Angelo

PostPosted: Sun Apr 17, 2005 3:15 pm    Post subject:  

Thats what I thought man. Heres my opinion I think they won't sell many of those things just because the friggin pink all over it. That's what think Cool
_________________
Did I do that? Hummmmmm!Yep, sure did!
Back to top  
Chris



Joined: 16 Apr 2004
Posts: 367
Location: Canada

PostPosted: Sun Apr 17, 2005 4:23 pm    Post subject:  

I like pink planes...but that scheme is just ugly, no matter what colours
_________________
-Chris-
3D Foamy
Back to top  
ryan



Joined: 13 Dec 2004
Posts: 147
Location: North Carolina

PostPosted: Sun Apr 17, 2005 5:29 pm    Post subject:  

I don't see what the problem with pink is. I love pink, several of my airplanes are covered pink. It's easy to see in the sky and I like the color itself. At the last TOC a pink airplane kicked everyone else's ass. And it had Budweiser logos on the ailerons. That's a manly airplane if i've ever seen one.
_________________
Ryan
Back to top  
Tom Uhlendorf



Joined: 18 Sep 2004
Posts: 563
Location: Morgan Hill, CA

PostPosted: Sun Apr 17, 2005 7:18 pm    Post subject:  

Applause Applause
Back to top  
 
   3DBatix Forum Index -> Workshop All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive