ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Any way to get more POWer from my Moki?
23 posts
 
   3DBatix Forum Index -> Gear Talk
 
Author Message
3D-kid330



Joined: 14 Nov 2004
Posts: 391
Location: Fremont, CA

PostPosted: Sat Feb 26, 2005 8:04 pm    Post subject: Any way to get more POWer from my Moki?  

All you guys with 3W and DA are spoiled rotten. I will probably never know what it is to have good power. My Edge flew great today, but there is barely enough power to pull out, so if you screw up the slightest with it, your done for. Any way to lighten it up or get more power out of it without comprimising reliability?

On a side note, the Edge had no rudder authority and had tail wag when flying. It was because the pull-pull cables were so loose that they had two inches of slop. After tightening them, it was like a different plane.

Thanks,
Brandon

_________________
Lower??!!


Last edited by 3D-kid330 on Sun Feb 27, 2005 3:57 pm; edited 1 time in total
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Sat Feb 26, 2005 9:22 pm    Post subject:  

start by tearing out some of the wood from under your canopy hatch. then use a dremel and rip a few un-needed bulkheads outta your mid-front fuse. do NOTHING to the wings. if you see some over hang from the splices in the wood with formers, take a lot of them out. i saved about 6 ounces doing the splice bulkeads and 2 ounces with the hatch. i saved half a pound in wood! as far as the motor goes, you really cant lighten that up. but you can take off your wheel pants and any pilots or inst. panels. theres 4-5 ounces to save. buy lighter wheels too. the lightest you can find. CF landing gear, CF tail assy. on your firewall, there is probably a lot of unneeded weight. ONLY take wood from the top and bottom of it thouhg. the sides are a MUST. cut lightening holes wherever you can. you have the Moki 1.8 so if you can get it to about 12.5-13 pounds you will have a lot more power. im working to get my edge down to 13.5 pounds. its at 14 now. the only other thing i can thin of is to buy a Moki 2.10. it has more power.
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
3D-kid330



Joined: 14 Nov 2004
Posts: 391
Location: Fremont, CA

PostPosted: Sat Feb 26, 2005 10:37 pm    Post subject:  

Cool! Thanks, a 14.5 lb plane with a 180 isn't that pleasant if you mess up. Not saying that to mess up is the thing to do, Rolling Eyes but if you do, you're screwed.

It pours out smoke now, so I wonder if I can go leaner? But I've had very bad experiences with lean Mokis. When mine went just 1 click lean, it lost power and bogged, then it just about died. And I was torque rolling at 2 feet tops. being evil It's better with the regulator and the clip that keeps the low end from spinning, so mabey I can go leaner without comprimising anything else?

Thanks,
Brandon

_________________
Lower??!!
Back to top  
Chris



Joined: 16 Apr 2004
Posts: 367
Location: Canada

PostPosted: Sat Feb 26, 2005 11:10 pm    Post subject:  

you could also use a cf wing tube
_________________
-Chris-
3D Foamy
Back to top  
3D-kid330



Joined: 14 Nov 2004
Posts: 391
Location: Fremont, CA

PostPosted: Sat Feb 26, 2005 11:28 pm    Post subject:  

It would be cool if I could, but I have a one piece wing. (Great for fitting into cars) Rolling Eyes

Thanks for the reply!

_________________
Lower??!!
Back to top  
Gezoid



Joined: 24 May 2004
Posts: 161
Location: UK

PostPosted: Sun Feb 27, 2005 1:05 am    Post subject:  

What prop you using on the Moki. I've been told many times by different people that 20 x 6 is the one for 3D on the Moki 1.8, especially the carbon Mejlik. Didn't try it myself as I chickened out and bought a 50cc gasser.

Oh yeah, and there's always tuned pipes.

_________________
Ya torkin' ta me?
Back to top  
3D-kid330



Joined: 14 Nov 2004
Posts: 391
Location: Fremont, CA

PostPosted: Sun Feb 27, 2005 2:01 am    Post subject:  

So the 20x6 Carbon Mejlick(sp??!!!!!????) will put out more thrust? I need as much as I can get. I currently run a Zinger 18x8, also ran Bambula 18x8 until I ran out of them. Rolling Eyes (the infamous flameout) laughing
_________________
Lower??!!
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Sun Feb 27, 2005 7:34 am    Post subject:  

Gezoid, Brandon is using the Moki 1.8. and the best prop for them is the one he's using. IM using a 2.10 and the best prop for that is a 20x8. Zak was happy with this prop too.
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Sun Feb 27, 2005 7:35 am    Post subject:  

3D-kid330 wrote:
So the 20x6 Carbon Mejlick(sp??!!!!!????) will put out more thrust? I need as much as I can get. I currently run a Zinger 18x8, also ran Bambula 18x8 until I ran out of them. Rolling Eyes (the infamous flameout) laughing

i think he means for the Moki 2.10. but even on the Moki 2.10 it wont put out as much as the 20x8.

_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
Chris



Joined: 16 Apr 2004
Posts: 367
Location: Canada

PostPosted: Sun Feb 27, 2005 9:22 am    Post subject:  

a 20x6 would have more pull then a 20x8 cause of the pitch...i think
_________________
-Chris-
3D Foamy
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Sun Feb 27, 2005 10:20 am    Post subject:  

no, a 2.10 would turn too many RPMs on a 20x6. ive tried one and it has less power than the 8.
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
Gezoid



Joined: 24 May 2004
Posts: 161
Location: UK

PostPosted: Sun Feb 27, 2005 1:05 pm    Post subject:  

No, I meant 20 x 6 carbon Mejlik for the Moki 1.8. Take a look at it, very slim blade. Supposed to be the best combo for static thrust on the 1.8 and that's using no nitro too - which Moki recommends, btw.

Try it, ya can always sell it if it's junk! laughing

Hang on, how do you spell it, let me get me prop...

Aha! It's MEJZLIK, cool. Sounds sexual in a Russian sort of way...

_________________
Ya torkin' ta me?
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Sun Feb 27, 2005 1:27 pm    Post subject:  

yyyeaaahhhhhh Eh?
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1178
Location: Sunnyvale, CA

PostPosted: Sun Feb 27, 2005 2:18 pm    Post subject:  

The Mejzliks, especially the new ones, are known to load the engine more. Dont be fooled by a slim blade. Its all in the airfoil. AirModels props have even THINNER blades, but pull even harder as long as you can spin them.

The 20x8 will have more thrust, since its more pitch. I think that the 20x6 on the 1.8 is way too much. It could spin it, but the response time on the throttle would be bad. I think sticking with an 18x8 on the Mokie 1.8 is the best way to go. Might just want to invest in a better prop, such as a Menz or Bambula.

_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
3D-kid330



Joined: 14 Nov 2004
Posts: 391
Location: Fremont, CA

PostPosted: Sun Feb 27, 2005 3:19 pm    Post subject:  

Would a Menz or Bambula 19x8 work better? (as far as spool up time and thrust)
_________________
Lower??!!
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1178
Location: Sunnyvale, CA

PostPosted: Sun Feb 27, 2005 5:44 pm    Post subject:  

It would be better, but i dont know if the Moki could spin that.
_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
3D-kid330



Joined: 14 Nov 2004
Posts: 391
Location: Fremont, CA

PostPosted: Sun Feb 27, 2005 6:50 pm    Post subject:  

Kip used one on his, not sure how it worked though.
_________________
Lower??!!
Back to top  
Gezoid



Joined: 24 May 2004
Posts: 161
Location: UK

PostPosted: Mon Feb 28, 2005 3:03 am    Post subject:  

What we need is someone who has actually used a 20 x 6 on a 1.8. Personally, I reckon it'll turn it, but what do I know, i aint actually done it? Yeah, 18 x 8 is the recommended prop so you would think if the pitch is decreased that you could turn more diameter, 19 x 6 for sure, and probably 20 x 6. Lower pitch props produce more thrust at low airspeed, just look at fun fly props. You don't see full size pilots taking of or landing in fully coarse do ya? Coarse is for go, fine is for slow. sly wink
_________________
Ya torkin' ta me?
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Mon Feb 28, 2005 5:18 am    Post subject:  

acually, i have seen a 20x6 used on a Moki 1.8. the guy had a brand new moki 1.8 with a sig 300xs. he took it up for the maiden and it flew great. next flight, he takes it up. about 6 minutes into his flight the engine quit. he was pretty high up so he had time to land it without much damage. he then checked all the fuel lines, plug, anything he could think of. then he just thought it was OK so he fueled it up, and tried to start it. but there was no compresion Rolling Eyes so we took the head off of the Moki and the the piston was all scratched and had wear marks all over it. keep in mind this guy is using fuel WITHOUT nitromethane.(what i use) so he had to buy another moki and try it agen. this time I told him to use an 18x10. it seems towork well for him now. o yeah, my dad has an 18x10 on a moki and it runs great. 8500 rpms.
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
Gezoid



Joined: 24 May 2004
Posts: 161
Location: UK

PostPosted: Mon Feb 28, 2005 6:44 am    Post subject:  

Can't see there'd be any loading difference on the engine between 18 x 10 and 20 x 6, honestly. Jeez, my ST G23 uses a 18 x 8 (recommended prop) and is giving away 7 cc's to the Moki. Interestingly, it produces lots more vertical thrust with an 18 x 6. Also my ST 3000 (30cc) will swing a 20 x 8 if pushed, no probs. The Moki is way more powerful than any of these so it should be okay.

Look, when I build something for my Moki I'll use the Mezjlik and see once and for all. You guys have me doubting myself now! Confused laughing

And another thing laughing laughing if that guy took up a brand new Moki on a 20 x 6 he deserves a wrecked engine! Couple of gallons real rich on a sensible prop before you'd try anything like that, especially on a Moki. Lots of guys swear by FIVE gallons of running in time.

_________________
Ya torkin' ta me?
Back to top  
ryan



Joined: 13 Dec 2004
Posts: 147
Location: North Carolina

PostPosted: Mon Feb 28, 2005 10:40 pm    Post subject:  

Butthead wrote:
acually, i have seen a 20x6 used on a Moki 1.8. the guy had a brand new moki 1.8 with a sig 300xs. he took it up for the maiden and it flew great. next flight, he takes it up. about 6 minutes into his flight the engine quit. he was pretty high up so he had time to land it without much damage. he then checked all the fuel lines, plug, anything he could think of. then he just thought it was OK so he fueled it up, and tried to start it. but there was no compresion Rolling Eyes so we took the head off of the Moki and the the piston was all scratched and had wear marks all over it. keep in mind this guy is using fuel WITHOUT nitromethane.(what i use) so he had to buy another moki and try it agen. this time I told him to use an 18x10. it seems towork well for him now. o yeah, my dad has an 18x10 on a moki and it runs great. 8500 rpms.


That sounds like a machining issue and QC issue, not because of what the guy did.

_________________
Ryan
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Tue Mar 01, 2005 4:46 am    Post subject:  

i dont think so. this also happened to me, but not because of prop size. i ran it too lean and didnt have enough cooling inmy cowl and it fried up.
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1178
Location: Sunnyvale, CA

PostPosted: Tue Mar 01, 2005 5:47 pm    Post subject:  

I took my Moki apart before it was ever turned over, and there were metal flakes (from machining) in the crank case and in the cylinder. Needless to say i cleaned em out.
_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
 
   3DBatix Forum Index -> Gear Talk All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive