ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

starting my saito
9 posts
 
   3DBatix Forum Index -> Gear Talk
 
Author Message
Flying French Dude



Joined: 29 Dec 2004
Posts: 43

PostPosted: Sat Feb 26, 2005 6:35 pm    Post subject: starting my saito  

tried to start my new saito .72 wasnt sucessful i know its not the glow plug

and i noticed when i tried to prime it by covering the muffler hole and back spinning the prop that the fuel wasnt going up much all the tubing was ok tho

gaz tank working good too

anyone has any idea i didnt touch the screw setting

FFD frown frown

_________________
any landing your plane survive in one peice ...
is a good landing
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Sat Feb 26, 2005 6:38 pm    Post subject:  

where is your tank? if is too low, you will have problems starting and running it.
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
Flying French Dude



Joined: 29 Dec 2004
Posts: 43

PostPosted: Sun Feb 27, 2005 3:48 am    Post subject:  

i mounted the engine on a board the tank is mounted on same board
same hight

FFD

_________________
any landing your plane survive in one peice ...
is a good landing
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Sun Feb 27, 2005 7:31 am    Post subject:  

hmm, thats odd. is your glow driver dead? they need to be at a VERY high charge to start the Siato's.
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Sun Feb 27, 2005 7:36 am    Post subject:  

also whn you prime it, try going counter clockwise. my Moki 2.10 primes counter clockwise better than clockwise.
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
Flying French Dude



Joined: 29 Dec 2004
Posts: 43

PostPosted: Sun Feb 27, 2005 9:30 am    Post subject:  

did go counterclock wise glow ignitor was fully charged got that plug red hot i checked

getting desperate frown frown

i heard so much good things about saito engine

FFD

_________________
any landing your plane survive in one peice ...
is a good landing
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1178
Location: Sunnyvale, CA

PostPosted: Sun Feb 27, 2005 5:46 pm    Post subject:  

Put your finger over the exhaust and spin the prop with the electric starter. Also, make sure the needles are open to the right setting.
_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
crookeder



Joined: 28 Nov 2004
Posts: 7
Location: Jacksonville Florida

PostPosted: Sun Feb 27, 2005 7:24 pm    Post subject: Saito72  

I had the same problem with my 72. It turned out that the low needle was never opened from the factory. It should be opened until it is flush with the throttle arm.After I finaly figured out what it was (it was already in the cowl of my Funtana) I never had to touch it again.
Back to top  
Flying French Dude



Joined: 29 Dec 2004
Posts: 43

PostPosted: Mon Feb 28, 2005 4:22 am    Post subject:  

cool ill try the needlle valve thingy and the electric starter

thanks for your help

FFD laughing laughing

_________________
any landing your plane survive in one peice ...
is a good landing
Back to top  
 
   3DBatix Forum Index -> Gear Talk All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive