ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Jak Nyfe!!!
16 of 31 posts archived
 
   3DBatix Forum Index -> Foamies
 
Author Message
TeamMoki3D



Joined: 08 Oct 2004
Posts: 430
Location: Belvidere, NJ

PostPosted: Fri Feb 04, 2005 7:31 pm    Post subject: Jak Nyfe!!!  

hey guys! my jak nyfe finally came!! this is an awsome plane Lee, thank you soo much! on saturday i'm going to get the battery, servos, and reciever. i will also be using the HIMAX 2812 0850 outrunner with a PHX 25amp esc. if they dont have the motor and ESC then ill get them from BPP. so far i have the stabalizer glued on and all of the surfaces hinged,(thanks to Lee, i only had to hinge the rudder!) next i'm going to mount the motor and hook up the servos and connections. lastly i will do the flying wires. thanks again Lee for an AWSOME plane. Cool Very Happy ill update soon!
_________________
"uhhhhhhhhh......Whoah! (uhuhuhhhuhh) I think I just figured something out...... this sucks!"


Last edited by TeamMoki3D on Fri Feb 04, 2005 7:36 pm; edited 1 time in total
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 924
Location: Fremont, CA

PostPosted: Fri Feb 04, 2005 7:35 pm    Post subject:  

Post some pics of your building process.
_________________
--Meyrick--
Back to top  
TeamMoki3D



Joined: 08 Oct 2004
Posts: 430
Location: Belvidere, NJ

PostPosted: Fri Feb 04, 2005 8:42 pm    Post subject:  

meyrick i sent some pics to your email. anddddd... i got the control horns glued in just now. since i dont have any foam safe CA, im using 5 min. epoxy(dollar store stuff, real light Wink ) tomorow i will pick up some of that CA too.
_________________
"uhhhhhhhhh......Whoah! (uhuhuhhhuhh) I think I just figured something out...... this sucks!"
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 924
Location: Fremont, CA

PostPosted: Fri Feb 04, 2005 10:21 pm    Post subject:  

Here are Saucy's pics.


JakNyfe 005.jpg
 Description:
 Filesize:  54.32 KB
 Viewed:  374 Time(s)

JakNyfe 005.jpg



JakNyfe 004.jpg
 Description:
 Filesize:  62.65 KB
 Viewed:  374 Time(s)

JakNyfe 004.jpg



JakNyfe 003.jpg
 Description:
 Filesize:  56.67 KB
 Viewed:  374 Time(s)

JakNyfe 003.jpg



JakNyfe 002.jpg
 Description:
 Filesize:  36.43 KB
 Viewed:  374 Time(s)

JakNyfe 002.jpg



JakNyfe 001.jpg
 Description:
 Filesize:  77.49 KB
 Viewed:  374 Time(s)

JakNyfe 001.jpg



_________________
--Meyrick--
Back to top  
N81U



Joined: 09 Aug 2004
Posts: 96
Location: Goodyear AZ

PostPosted: Sat Feb 05, 2005 12:40 am    Post subject:  

Did you need the instructions? I do not have a printable version yet, if you print it out it would be as long as War and Peace, that is why I burned the CD for you. This may be the way to go. What do you think?

Happy flying
Lee
Back to top  
TeamMoki3D



Joined: 08 Oct 2004
Posts: 430
Location: Belvidere, NJ

PostPosted: Sat Feb 05, 2005 5:11 am    Post subject:  

yeah, i agree. it saves a LOT of time. im half way done and i got it yesterday! this morning i got the elevator servo in in the exact spot as in the CD and the elevator linkage hooked up in the same spot. do you want me to make a review for it? Or did you do that already?
BTW, those CF rods are exelent and take 10 seconds to make! that saves a bunch of time and effort too! thanks!

-Saucy-

_________________
"uhhhhhhhhh......Whoah! (uhuhuhhhuhh) I think I just figured something out...... this sucks!"
Back to top  
N81U



Joined: 09 Aug 2004
Posts: 96
Location: Goodyear AZ

PostPosted: Sat Feb 05, 2005 10:57 am    Post subject:  

No review is nessasary you have done your job, Thank you. Those pushrods are very long so be sure to use 1 or 2 standoffs to give them support. They will flex at higher speeds

Lee
Back to top  
TeamMoki3D



Joined: 08 Oct 2004
Posts: 430
Location: Belvidere, NJ

PostPosted: Sat Feb 05, 2005 11:00 am    Post subject:  

ok, gotcha! Wink thanks.
are the flying wires really necessary? or can i replace them with some carbon fiber rods in the wings?

_________________
"uhhhhhhhhh......Whoah! (uhuhuhhhuhh) I think I just figured something out...... this sucks!"
Back to top  
N81U



Joined: 09 Aug 2004
Posts: 96
Location: Goodyear AZ

PostPosted: Sat Feb 05, 2005 1:00 pm    Post subject:  

Yes some type of support is nessasary, you can put carbon in the wings but that would not be easy to do after it is built and it will weigh more. Flat carbon on the L.E. of both wings would be your best bet if you decided to not use the wires. 1/16 solid carbon like the push rod materal could replace the wires also. My best advice is to stick with the flying wires that the plans show it is easy to do. One of the reasons it took so long to get the plane to you was time spent pondering things just like this, Have fun with your bipe and remember no mater how you do it the JakNyfe will fly great.

Lee
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 924
Location: Fremont, CA

PostPosted: Sat Feb 05, 2005 5:39 pm    Post subject:  

Did some bad ass video today with ZAK of this baby and a couple of old farts chewed us for flying behind the flightlines. Laughing Zak is doing the editing on the vid and should be up shortly.
_________________
--Meyrick--
Back to top  
TeamMoki3D



Joined: 08 Oct 2004
Posts: 430
Location: Belvidere, NJ

PostPosted: Sat Feb 05, 2005 7:49 pm    Post subject:  

well, i decided to go with the carbon fiber rods in the wings. they are VERY stiff so i dont think it will be a problem. al;so, i got the AXI 2212 26! which is WAYYYY more than enough power. also got a e-flite 20amp esc and a electrifly 1500mah lipoly(11.1volts)
_________________
"uhhhhhhhhh......Whoah! (uhuhuhhhuhh) I think I just figured something out...... this sucks!"
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 924
Location: Fremont, CA

PostPosted: Sat Feb 05, 2005 7:57 pm    Post subject:  

TeamMoki3D wrote:
well, i decided to go with the carbon fiber rods in the wings.


I just put a carbon on the bottom wing. The top wing does not need it.

_________________
--Meyrick--
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 924
Location: Fremont, CA

PostPosted: Sat Feb 05, 2005 9:08 pm    Post subject:  

JakNyfe Video
_________________
--Meyrick--
Back to top  
Chris



Joined: 16 Apr 2004
Posts: 270
Location: Toronto, Canada

PostPosted: Sat Feb 05, 2005 9:43 pm    Post subject:  

TeamMoki3D wrote:
well, i decided to go with the carbon fiber rods in the wings. they are VERY stiff so i dont think it will be a problem. al;so, i got the AXI 2212 26! which is WAYYYY more than enough power. also got a e-flite 20amp esc and a electrifly 1500mah lipoly(11.1volts)


Is that a BL esc? I think I maybe in the market for a new one...I know you have the BL motor but haven;t seen anythign about e-flite escs Let us know!!

_________________
-Chris-
3D Foamy
Back to top  
TeamMoki3D



Joined: 08 Oct 2004
Posts: 430
Location: Belvidere, NJ

PostPosted: Sun Feb 06, 2005 5:57 am    Post subject:  

hey zak, a few questions about your JakNyfe...
what did it weigh w/o battery?
what servos were you using?
thanks!

_________________
"uhhhhhhhhh......Whoah! (uhuhuhhhuhh) I think I just figured something out...... this sucks!"
Back to top  
15 posts here were not archived
TeamMoki3D



Joined: 08 Oct 2004
Posts: 397
Location: Belvidere, NJ

PostPosted: Tue Feb 08, 2005 6:04 am    Post subject:  

not 3/8! 3/16 sorry, typo
_________________
"uhhhhhhhhh......Whoah! (uhuhuhhhuhh) I think I just figured something out...... this sucks!"
Back to top  
 
   3DBatix Forum Index -> Foamies All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive