ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Funtana 90, what else
10 posts
 
   3DBatix Forum Index -> 3D Talk
 
Author Message
El Diablo



Joined: 10 Jan 2005
Posts: 37

PostPosted: Mon Jan 10, 2005 4:26 pm    Post subject: Funtana 90, what else  

Hey guys I'm putting a Funtana 90 together like everyone else and I wanted to get a few second opinions on my set-up. First are any of you guys using an FM radio or all PCM. #2 I saw a plane with the throttle servo on the firewall, is there a downside to this set-up other than fuel on the servo. BTW I was thinking of running exh. ext to get it all the way out of the cowl. #3 Are those of you running a YS 1.10 using the stock muffler? And last but not least, is pinning the firewall really necessary.
_________________
If you aint crashin'... you aint pushin' the envelope.
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 924
Location: Fremont, CA

PostPosted: Mon Jan 10, 2005 6:30 pm    Post subject:  

I haven't built mine but I was thinking of glassing the outside corners of the firewall with some 2oz. fiber cloth. I got a spare PCM so I will go with a PCM. FM should be fine with these. And I haven't decided whether I'm gonna go with a YS1.10 or Saito1.20. Either motor, I'm going with a pull-pull rudder.
_________________
--Meyrick--
Back to top  
TeamMoki3D



Joined: 08 Oct 2004
Posts: 430
Location: Belvidere, NJ

PostPosted: Tue Jan 11, 2005 8:14 pm    Post subject:  

every plane up until my bme edge i HAVE'NT pinned my firewall. so it is not necessary but it gives you a good felling about the strength of your plane.
hope this helps

_________________
"uhhhhhhhhh......Whoah! (uhuhuhhhuhh) I think I just figured something out...... this sucks!"
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 193
Location: Jackson, MS

PostPosted: Mon Jan 24, 2005 9:01 pm    Post subject: Re: Funtana 90, what else  

El Diablo wrote:
Hey guys I'm putting a Funtana 90 together like everyone else and I wanted to get a few second opinions on my set-up. First are any of you guys using an FM radio or all PCM. #2 I saw a plane with the throttle servo on the firewall, is there a downside to this set-up other than fuel on the servo. BTW I was thinking of running exh. ext to get it all the way out of the cowl. #3 Are those of you running a YS 1.10 using the stock muffler? And last but not least, is pinning the firewall really necessary.



My answers:
1) I use a FM Rx, PCM would work fine also if you have it already.
2) Possible fuel and exhaust getting on and maybe in the servo at worst case scenerio. I am using a HS-85 for my throttle in the stock location.
3) I used the stock muffer on my YS 1.10FZ until the straight pipe snapped at the diameter reduction portion on the stock muffler. I replaced it with a PSPEC muffler with a 30 degree angle. Has a very deep growl. Sounds great. Not sure if any power was gained.
4) I did pin the firewall as I have seen some of these firewalls pull out completely clean. I did pin and tri-stocked the engine box. Even if it didn't need it, it only took 10-20 minutes to do and gave me some piece of mind.

_________________
Fly it hard and hover it low...

My RC Photo Page


Last edited by DTB on Tue Jan 25, 2005 8:09 am; edited 1 time in total
Back to top  
Gezoid



Joined: 24 May 2004
Posts: 88
Location: UK

PostPosted: Tue Jan 25, 2005 6:14 am    Post subject:  

Any opinions on using a Super Tigre G23 or Moki 1.35 in the F90?
Back to top  
TeamMoki3D



Joined: 08 Oct 2004
Posts: 430
Location: Belvidere, NJ

PostPosted: Wed Jan 26, 2005 3:21 pm    Post subject:  

i wouldnt go with the Super Tigre because, from experience, they all come with the wrong carb!. i was gonna get the G3500 from them but they gave me the G4500 carb and it wouldnt fit. a new carb was gonna cost 75 bucks!! so i sent it back and got a Moki 2.10(35cc) i LOVE IT moki's are probably the best 2 strokes you can buy for 1/4 scale and under.
_________________
"uhhhhhhhhh......Whoah! (uhuhuhhhuhh) I think I just figured something out...... this sucks!"
Back to top  
Gezoid



Joined: 24 May 2004
Posts: 88
Location: UK

PostPosted: Wed Jan 26, 2005 3:57 pm    Post subject:  

Yeah, you're right, but I already have the Tigre and I was thinking of getting the Perry 5200 carb' and V30 pump. Guy on RCU reckons it works out good.

I'd really like the Moki 1.35 but it's £180 and then I gotta get a silencer too at about £50 and maybe a pump. Actually, I'd really like a Saito 1.50 but that's like £340! And there's some doubt about the Saito's on low nitro, which is all we can afford here as nitro is so expensive. Evil or Very Mad

All the big Tigre's had duff carb's, real rich midrange. They're supposed to have sorted this on the Chinese made engines. Mine is Italian made so I have to switch the carb anyway to 3D, s'why I thought I'd get the perry and a pump and move the tank over the CG.
Back to top  
TeamMoki3D



Joined: 08 Oct 2004
Posts: 430
Location: Belvidere, NJ

PostPosted: Wed Jan 26, 2005 6:19 pm    Post subject:  

well, moki's run on 0% nitro Cool absolutely NO nitro!
_________________
"uhhhhhhhhh......Whoah! (uhuhuhhhuhh) I think I just figured something out...... this sucks!"
Back to top  
3D-kid330



Joined: 14 Nov 2004
Posts: 123
Location: Fremont, Ca

PostPosted: Wed Jan 26, 2005 9:16 pm    Post subject:  

I've seen some people using an RCS 140(I think that's what it was) gasser that works pretty well if you keep it light.
_________________
Lower??!!
Back to top  
Gezoid



Joined: 24 May 2004
Posts: 88
Location: UK

PostPosted: Thu Jan 27, 2005 1:50 am    Post subject:  

TeamMoki3D wrote:
well, moki's run on 0% nitro Cool absolutely NO nitro!


Yeah, big Tigres are happy on no nitro too.
Back to top  
 
   3DBatix Forum Index -> 3D Talk All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive