| |
| Author |
Message |
Flying French Dude
Joined: 29 Dec 2004 Posts: 43
|
Posted: Fri Jan 07, 2005 6:20 pm Post subject: those hellish CA hinges |
|
|
ok i am all happy
got my new funtana this morning i start to assemble the plane then i come to fix the aileron to the wing and bam !!!
those (pUT BAD WORDS IN HERE ) CA hinges ... anyone knows an easy way to make then go in there slot !!! i got 5 per aileron i put them in the aileron fine but when i come to put them in the wing
they need to go in there kind of at the same time and they just twist and bend and....
reading the manual didnt help me
i know you guys are probably R.O.F.L. at me right now
but this is my first arf i put together PLEASE any help will be welcome _________________ any landing your plane survive in one peice ...
is a good landing |
|
| Back to top |
|
 |
Tom Uhlendorf

Joined: 18 Sep 2004 Posts: 563 Location: Morgan Hill, CA
|
Posted: Fri Jan 07, 2005 6:35 pm Post subject: |
|
|
First off, don't use CA hinges. They break WAY to easy. Get some dubro pined hinges or something. Then get an A-Xacto knife and very carfuly, with out over sizing it, work the blade back and fowarth until the hinge fits farly snugg. Then glue it in with some epoxy or better RC-56. It is very time consuming and takes lots of patients to do a good job. You can get some hinge sloting tools but I don't think you need them unless you are using heavy duty(HD) hinges.
Hope this helps. |
|
| Back to top |
|
 |
Chris

Joined: 16 Apr 2004 Posts: 367 Location: Canada
|
Posted: Fri Jan 07, 2005 7:04 pm Post subject: |
|
|
I think Ca hinges will be fine I know 2 master builders tha use ca hinges on their jets even, I have them n a 90 size plane i'm building _________________ -Chris-
3D Foamy |
|
| Back to top |
|
 |
john wondra

Joined: 05 May 2004 Posts: 360 Location: auburn, wa
|
Posted: Fri Jan 07, 2005 8:06 pm Post subject: |
|
|
i have ca hinges on my 35% extra. they broke at a contest......i was franticly re hingeing. they lasted about 3 years, they eventually break but on a smaller plane they should work fine. pin hines are nice, but there a pain in the ass and a waste of time(IMO) on smaller planes. john _________________ John Wondra RAMS VP
Team 3D Foamy/3D Foamy Suport
__________________________
www.3dfoamy.com
www.northwest3d.com
www.e-flightline.com
www.Falconbatteries.com
www.cutimages.com <all your custom vinyl needs> |
|
| Back to top |
|
 |
3Dfanatic
Joined: 15 Apr 2004 Posts: 300 Location: Tacoma(area), WA
|
Posted: Fri Jan 07, 2005 9:38 pm Post subject: |
|
|
CA hinges are fine for something that size. The easiest way to get a CA hinge in the slot is to have the slot the right size. Typically they come too small... Not much though so be careful. _________________ -Aaron
cutimages.com
offthewallrc.com |
|
| Back to top |
|
 |
3dbatixkid Moderator

Joined: 15 Apr 2004 Posts: 1178 Location: Sunnyvale, CA
|
|
| Back to top |
|
 |
Gezoid

Joined: 24 May 2004 Posts: 161 Location: UK
|
Posted: Sun Jan 09, 2005 11:00 am Post subject: |
|
|
I wouldn't use 'em after both the outside one's on my Funtana elevator broke. Can't tell you the pain of trying to cut 'em out. Spoiled the plane for keeps Mind, the rest are still in there so far.
Get some decent pin hinges is my advice.  |
|
| Back to top |
|
 |
Tom Uhlendorf

Joined: 18 Sep 2004 Posts: 563 Location: Morgan Hill, CA
|
Posted: Sun Jan 09, 2005 12:58 pm Post subject: |
|
|
| Yep, get some pined. It will save you so much ttrouble in the LONG run.(MHO). |
|
| Back to top |
|
 |
DTB

Joined: 24 Jul 2004 Posts: 460 Location: Danville, VA
|
Posted: Mon Jan 10, 2005 11:14 am Post subject: |
|
|
I used Robart Hinges on my FT90. They work great, but just takes a little longer to install, but the results are worth the effort IMHO.
You can view my FT90 construction by clicking here _________________ Fly it hard and hover it low...
My RC Photo Page |
|
| Back to top |
|
 |
| |