ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

saito 72 break in
10 posts
 
   3DBatix Forum Index -> Gear Talk
 
Author Message
Flying French Dude



Joined: 29 Dec 2004
Posts: 43

PostPosted: Mon Jan 03, 2005 7:53 am    Post subject: saito 72 break in  

ok got my new engine today a nice saito .72 i plan to put it in a funtana .40

how should i go about getting it ready ?

should i just slap it on the funtana and run it a bit rich for the first fews flights ( How many)
or should i bolt it on a bench and run it (how long) from there.

another solution maybe to put it in my trainer for a fews flights..

.
please tell me what is best

i use 15% fue

also should i use a different prop for roding i plan to fly the funtana with a 12x6 getting use to it then move to a 14x4w for 3d

_________________
any landing your plane survive in one peice ...
is a good landing
Back to top  
Shane



Joined: 26 Dec 2004
Posts: 32
Location: Nova Scotia

PostPosted: Mon Jan 03, 2005 8:05 am    Post subject:  

Do what the manual says, and keep it in a certain RPM range, which is in the manual. I dont have any 4 bangers right now, but my friend just bought an Saito 91 and thats what he did. Keep it rich aswell. I'd say put it in the Funtana and fly it. I'd go with the 14x4w right now, because 12x6 may fly it too fast.

Shane
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 460
Location: Danville, VA

PostPosted: Mon Jan 03, 2005 8:11 am    Post subject: Re: saito 72 break in  

Flying French Dude wrote:
ok got my new engine today a nice saito .72 i plan to put it in a funtana .40

how should i go about getting it ready ?

should i just slap it on the funtana and run it a bit rich for the first fews flights ( How many)
or should i bolt it on a bench and run it (how long) from there.

another solution maybe to put it in my trainer for a fews flights..

.
please tell me what is best

i use 15% fue

also should i use a different prop for roding i plan to fly the funtana with a 12x6 getting use to it then move to a 14x4w for 3d


I broke my Saito 40 in by the saito book and it runs fantastic. I bench ran it at first, then ran it a little rich on the plane and leaned it out more after a gallon or so. Need to let the ring set properly.

A 12x6 will probably put a little less load on the engine than the 14x4. Most use a 14x4 for 3d mainly, a 13x6-8 for general flying.

The 12x6 would put the same load as a 14x2.

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
Flying French Dude



Joined: 29 Dec 2004
Posts: 43

PostPosted: Mon Jan 03, 2005 11:18 am    Post subject:  

ty for the info

what i want is for the plane to have awsome vertical i want it to climb well so is the 12x6 better or should i go with the 13x6

thanks again

_________________
any landing your plane survive in one peice ...
is a good landing
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 1316
Location: Fremont, CA

PostPosted: Mon Jan 03, 2005 11:40 am    Post subject:  

Flying French Dude wrote:
ty for the info

what i want is for the plane to have awsome vertical i want it to climb well so is the 12x6 better or should i go with the 13x6

thanks again


In my opinion a wider lower pitch prop would give you better vertical. Start out with an APC 13x4W then when the motor is broken in go to 14x4w

_________________
--Meyrick--
Back to top  
DTB



Joined: 24 Jul 2004
Posts: 460
Location: Danville, VA

PostPosted: Mon Jan 03, 2005 11:59 am    Post subject:  

Meyrick wrote:
Flying French Dude wrote:
ty for the info

what i want is for the plane to have awsome vertical i want it to climb well so is the 12x6 better or should i go with the 13x6

thanks again


In my opinion a wider lower pitch prop would give you better vertical. Start out with an APC 13x4W then when the motor is broken in go to 14x4w


ditto. Vertical performance is better with lower pitch. The 12x6 will fly you faster, but with less vertical pull. 14x4 will fly slower with more vertical pulling power.

_________________
Fly it hard and hover it low...

My RC Photo Page
Back to top  
Tom Uhlendorf



Joined: 18 Sep 2004
Posts: 563
Location: Morgan Hill, CA

PostPosted: Mon Jan 03, 2005 3:53 pm    Post subject:  

I would stay with the 13x4W. My dad has a 72 and we put a 14x4W on it. It had really slow transition speed. The vertical is good but, not worth it because the time to run up is like a turbine.

Also, I might add, we tuned that thing with a tachometer for two hours and didn't make difference. And my dad is a genius for tuning motors. Nothing changed.
Back to top  
Ramz



Joined: 05 Nov 2004
Posts: 55
Location: New Brunswick, Canada

PostPosted: Sat Jun 18, 2005 10:44 am    Post subject: saito prop  

I've put about 4 gallons through my 72 with a 13x4W and it's loving it. It'll spin it at 10,700 on 15% pink stuff. I broke it in as per the manual and took it easy for the first 10 flights. It's the sweetest running glow motor I own by far. Pulls my Twist out a hover fairly decent although a 82 would be that much better in this application. I believe a 14x4W would load the engine up too much for good 3D. Go with a 13x4W.
Back to top  
JR.Master



Joined: 07 Nov 2004
Posts: 462
Location: San Angelo

PostPosted: Sat Jun 18, 2005 12:20 pm    Post subject:  

run it on a test stand first i'd rahter do that than take my chances with it running rich on the funtana big grin
_________________
Did I do that? Hummmmmm!Yep, sure did!
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Sat Jun 18, 2005 2:16 pm    Post subject:  

just fly it to break it in. test stands are worthless for break-in. the only other thing i would do besides fly it is run it up on the ground without flying it. test satnds take too long to setup and use, IMO. just my $00.02.
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
 
   3DBatix Forum Index -> Gear Talk All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive