| |
| Author |
Message |
3D-kid330

Joined: 14 Nov 2004 Posts: 391 Location: Fremont, CA
|
Posted: Wed Dec 29, 2004 11:25 pm Post subject: Axi and Castle Creations Pheonix 25 gets hot. |
|
|
Got an Axi & a Phx. 25for Christmas along with a new 9303. Ran up the Axi 2212 / 34, and the Pheonix 25 gets warm/hot within a minute of plugging in the battery. (3s1p 1350) Is this normal? I really can't afford to fry these.
Here's how I programmed it:
Cutoff set to 9.0V
Current limiting left to default at standard(cause it has a warning that says change this at your own risk )
Hard delayed brake
Auto calibrating throttle
Standard advance timing
Hard cutoff
Soft start
Shoud I change anything here?
I was amazed at how powerful, quiet, and efficent the Axi is.
Thanks in advance,
Brandon _________________ Lower??!! |
|
| Back to top |
|
 |
Meyrick Site Admin

Joined: 15 Apr 2004 Posts: 1316 Location: Fremont, CA
|
Posted: Wed Dec 29, 2004 11:35 pm Post subject: |
|
|
What prop are you swinging bro? _________________ --Meyrick-- |
|
| Back to top |
|
 |
Flatlandmike

Joined: 29 Oct 2004 Posts: 31
|
Posted: Thu Dec 30, 2004 10:42 am Post subject: |
|
|
the prop would be the difference
example castle creation 25 amp sped control park 400 3s1p
with the 12x6 horizon sends gets 23 max amps with a 12x6 apc sf it pulls 13 amps huge difference _________________ www.lmacky.org |
|
| Back to top |
|
 |
3D-kid330

Joined: 14 Nov 2004 Posts: 391 Location: Fremont, CA
|
Posted: Thu Dec 30, 2004 11:40 am Post subject: |
|
|
I'm swinging a GWS 10/4.7 cause that's what I had laying around.
Also, the Pheonix gets hot without running the motor in about 60 sec. Not extremely hot but enough to get me thinking that I might be frying this thing.
It's not mounted on a plane right now; I was bench testing.
Thanks,
Brandon _________________ Lower??!! |
|
| Back to top |
|
 |
Flatlandmike

Joined: 29 Oct 2004 Posts: 31
|
Posted: Thu Dec 30, 2004 12:03 pm Post subject: |
|
|
i have no clue then  _________________ www.lmacky.org |
|
| Back to top |
|
 |
Meyrick Site Admin

Joined: 15 Apr 2004 Posts: 1316 Location: Fremont, CA
|
Posted: Thu Dec 30, 2004 12:07 pm Post subject: |
|
|
| 3D-kid330 wrote: | I'm swinging a GWS 10/4.7 cause that's what I had laying around.
Also, the Pheonix gets hot without running the motor in about 60 sec. Not extremely hot but enough to get me thinking that I might be frying this thing.
It's not mounted on a plane right now; I was bench testing.
Thanks,
Brandon |
Hmm, I never touched the ESC before so I will check it out later and let you know.
How many servos do you have connected and make sure none of them are binding. _________________ --Meyrick-- |
|
| Back to top |
|
 |
3D-kid330

Joined: 14 Nov 2004 Posts: 391 Location: Fremont, CA
|
Posted: Thu Dec 30, 2004 2:22 pm Post subject: |
|
|
Actually, no servos hooked up. Just Reciever, Pheonix, Axi, and battery.
Thanks,
Brandon _________________ Lower??!! |
|
| Back to top |
|
 |
3D-kid330

Joined: 14 Nov 2004 Posts: 391 Location: Fremont, CA
|
Posted: Sat Jan 01, 2005 6:28 pm Post subject: |
|
|
Also, when I run it, it wobbles like crazy. Still haven't figured out why it gets warm/hot when I plug in the battery. (3s1p 1320) _________________ Lower??!! |
|
| Back to top |
|
 |
Meyrick Site Admin

Joined: 15 Apr 2004 Posts: 1316 Location: Fremont, CA
|
Posted: Sat Jan 01, 2005 7:50 pm Post subject: |
|
|
| 3D-kid330 wrote: | Also, when I run it, it wobbles like crazy. |
That's normal with the 25amp ESC at startup. All of mine does that. But once the prop is spinning with momentum, it's fine. _________________ --Meyrick-- |
|
| Back to top |
|
 |
3D-kid330

Joined: 14 Nov 2004 Posts: 391 Location: Fremont, CA
|
Posted: Sun Jan 02, 2005 12:35 am Post subject: |
|
|
I see. I guess that you really have to balance your props too. I havent ran it up all the way yet, but at super low throttles it's hard to hold. I only do it for a second so I don't damage the motor.
Is it normal for the Pheonix to get hot?
Thanks,
Brandon _________________ Lower??!! |
|
| Back to top |
|
 |
| |