ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

what setup and hardware for Funtana .40 with saito 72 eng
10 posts
 
   3DBatix Forum Index -> Gear Talk
 
Author Message
Flying French Dude



Joined: 29 Dec 2004
Posts: 43

PostPosted: Wed Dec 29, 2004 5:46 am    Post subject: what setup and hardware for Funtana .40 with saito 72 eng  

hi First of all Great forum

i am new to this hobby well kinda new i am able to fly my trainer and land it in one peice... well .. most of the time hehe

for second plane i got my self a funtana s .40 and deceided to go with the recomended engine saito 72 i use a Futaba exa 6 ch radio

i ordered a flight pack with 5 s3004 servo are they enought for this plane ?

i was wandering is the hardware coming with the kit ok or should i change
some of it ?

and also is there anything special i should do to programe my radio

any tips will be apreciated ty

_________________
any landing your plane survive in one peice ...
is a good landing
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Wed Dec 29, 2004 6:30 pm    Post subject:  

this is a PRETTY good second plane, not the first i would have recommended. are you planning on learning 3D? either way this is a great combo and yes the 3004's should be enough if you dont fly it too hard. not so sure about the hardware.. but your radio is a good choice and no special programing is neccessary right now! good luck with it and remember, this hobby is all about fun!
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
Radioflyer



Joined: 14 Sep 2004
Posts: 344
Location: Kalamazoo, MI

PostPosted: Wed Dec 29, 2004 6:44 pm    Post subject:  

FFD, Do you have a Sim that you're practicing on? The Funtana .40 can be gentle or wild. If you have alot of stick time on sims., than it can be a second. You need to be able to stay on top of it, because it isn't as forgiving as a trainer big grin
_________________
God bless us all, and keep us safe.


www.bryanhusk.com/jay
Back to top  
Shane



Joined: 26 Dec 2004
Posts: 32
Location: Nova Scotia

PostPosted: Wed Dec 29, 2004 7:34 pm    Post subject:  

Hey, I just got one of these myself, this will be my 3rd plane. Gl.
Back to top  
Flying French Dude



Joined: 29 Dec 2004
Posts: 43

PostPosted: Thu Dec 30, 2004 7:41 pm    Post subject:  

TeamMoki3D wrote:
this is a PRETTY good second plane, not the first i would have recommended. are you planning on learning 3D? either way this is a great combo and yes the 3004's should be enough if you dont fly it too hard. not so sure about the hardware.. but your radio is a good choice and no special programing is neccessary right now! good luck with it and remember, this hobby is all about fun!


thanks yes i plan to learn 3D slowly but surely right now i shake my trainer in ways i didnt tink were possible (i am really surprise at what the thing can do ) next spring i plan to fix wheels on the back and try an inverted landind last summer we had a limbo contest i came in second only because i didnt have retracts lol i live in canada so now its winter and all i can do is dream about spring and whatch those awsome vids you guys put on this site

radioflyer no i dont have lots of stick time on a sim.. i dont have one but i plan to take it slow and we got nice instructors at the feild plus i still got my fearless trainer to shake and bake when i feel like it lol

oh one last thing what prop should i get with the saito 72 ?

_________________
any landing your plane survive in one peice ...
is a good landing
Back to top  
3D-kid330



Joined: 14 Nov 2004
Posts: 391
Location: Fremont, CA

PostPosted: Thu Dec 30, 2004 8:06 pm    Post subject:  

Go for it. big grin Watch out for tip stalls, and get used to it up high at first. Test the stall up high, and set up dual rates. Keep a forward CG at first. You can always move CG aft and increase travel when you want do do 3D.
_________________
Lower??!!
Back to top  
Butthead



Joined: 08 Oct 2004
Posts: 1054
Location: Belvidere, NJ

PostPosted: Thu Dec 30, 2004 8:37 pm    Post subject:  

for the saito 72 i would either get a 12x6 or a 12x8 or a 13x6..i used a 12x6 and it was awsome, but for 3d use a 14x4W.. all 2 blade of coarse
_________________
John Paragallo

WildHare RC Extra 330LX 36%/ZDZ 120

Hangar-9 Extra 260 27%/ZDZ 50

Futaba 9C
Back to top  
Flying French Dude



Joined: 29 Dec 2004
Posts: 43

PostPosted: Fri Dec 31, 2004 5:07 am    Post subject:  

3D-kid330 wrote:
Go for it. big grin Watch out for tip stalls, and get used to it up high at first. Test the stall up high, and set up dual rates. Keep a forward CG at first. You can always move CG aft and increase travel when you want do do 3D.


after reading you i went to my radio instruction book just tell me if i get this dual rate thing right ...

its like i can set the travel the servo does 2 different ways from the same input of the stick and i choose between the 2 with a switch on my radio

so i can have my stick making the servo travel more for 3d and less for regular flight

is this better then using exponential ?

thanks for the info i never played much with the radio program thing

Francis aka Flying French Dude

_________________
any landing your plane survive in one peice ...
is a good landing
Back to top  
3D-kid330



Joined: 14 Nov 2004
Posts: 391
Location: Fremont, CA

PostPosted: Fri Dec 31, 2004 11:53 am    Post subject:  

Flying French Dude wrote:


its like i can set the travel the servo does 2 different ways from the same input of the stick and i choose between the 2 with a switch on my radio

so i can have my stick making the servo travel more for 3d and less for regular flight

Francis aka Flying French Dude


Thats correct. big grin I use the exponential also because it makes the center of the travel softer so that it's not as twitchy, but you will still have the same travel at the end-point of the stick.

I think that the manual for the airplane has a reccomendation on how much travel and exponential should be programmed as a starting point for test flying.

I hope I was clear in how I said it. sly wink

_________________
Lower??!!
Back to top  
Radioflyer



Joined: 14 Sep 2004
Posts: 344
Location: Kalamazoo, MI

PostPosted: Fri Dec 31, 2004 12:59 pm    Post subject:  

I found that my Funtana was uncontrolable at high rates w/o expo idea! I highly recomend useing the dual rates and expo. Like 3D-Kid330 said, do everything up high to get use to it. Once your comfortable w/ the plane you may end up leaving the rates on high w/ 30%-50% expo, thats when you have fun from start to finish big grin
_________________
God bless us all, and keep us safe.


www.bryanhusk.com/jay
Back to top  
 
   3DBatix Forum Index -> Gear Talk All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive