ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

How do you guys do your snaps?
25 posts
 
   3DBatix Forum Index -> IMAC, Pattern
 
Author Message
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 1316
Location: Fremont, CA

PostPosted: Mon Apr 26, 2004 9:04 pm    Post subject: How do you guys do your snaps?  

I use the elevator first, then aileron & rudder at the same time while releasing the elevator and finish off with ailerons.
_________________
--Meyrick--
Back to top  
3Dfanatic



Joined: 15 Apr 2004
Posts: 300
Location: Tacoma(area), WA

PostPosted: Tue Apr 27, 2004 9:12 am    Post subject:  

I try to lead with the elevator and release them all at the same time. Actually, at the last IMAC I just cranked them all on at the same time and off at the same time and got an 8 hehe
_________________
-Aaron

cutimages.com
offthewallrc.com
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 1316
Location: Fremont, CA

PostPosted: Tue Apr 27, 2004 10:17 am    Post subject:  

Zak always buries the sticks on the corner and release. Some judges wants to see that elevator break first.
_________________
--Meyrick--
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1177
Location: Sunnyvale, CA

PostPosted: Tue Apr 27, 2004 3:32 pm    Post subject:  

Hey now, thats a lie. Watch my 3/4 downline snap on my humpty bump, the elevator clearly goes in first. Watch my thumbs when i fly the sequence.
_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
recon



Joined: 27 Apr 2004
Posts: 2
Location: Medicine Hat, Alberta, Canada

PostPosted: Tue Apr 27, 2004 4:05 pm    Post subject:  

I dont fly in any competitions (not good enough) but when ever I did snaps I just cranked them all to the corner. I think this will be a helpful site, lots if neato tips!
_________________
I don't drive fast, I fly low!
BradyFlys
Medicine Hat R.C'ers

MAAC #63500J
Back to top  
3Dfanatic



Joined: 15 Apr 2004
Posts: 300
Location: Tacoma(area), WA

PostPosted: Wed Apr 28, 2004 9:01 pm    Post subject:  

Ya, we rock laughing
_________________
-Aaron

cutimages.com
offthewallrc.com
Back to top  
john wondra



Joined: 05 May 2004
Posts: 360
Location: auburn, wa

PostPosted: Wed May 05, 2004 3:36 pm    Post subject:  

the elevator should break first but alota judges arnt good enough to watch for it.
_________________
John Wondra RAMS VP
Team 3D Foamy/3D Foamy Suport
__________________________
www.3dfoamy.com
www.northwest3d.com
www.e-flightline.com
www.Falconbatteries.com
www.cutimages.com <all your custom vinyl needs>
Back to top  
Vic3D



Joined: 16 May 2004
Posts: 39

PostPosted: Sun May 16, 2004 9:20 pm    Post subject:  

Hey guys, pardon my ignorance, I am from Puerto Rico and sicne we speak spanish I dunno what a snap is, can someone please guide me here? Thanks!
Victor

_________________
Epoxy cures better in the air.
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1177
Location: Sunnyvale, CA

PostPosted: Sun May 16, 2004 9:22 pm    Post subject:  

its the stalled maneuver performed with elevator first to break the nose away from the line of flight, and then rudder and aileron (same direction) to make it "snap" back around to the line of flight again...

or am i too technical?

_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
3Dfanatic



Joined: 15 Apr 2004
Posts: 300
Location: Tacoma(area), WA

PostPosted: Mon May 17, 2004 9:00 am    Post subject:  

Just pull the sticks to the corners and that's a sortasnap haha.

Ryan Winslow let me fly his CompARF 2.6m Extra yesterday. WOW! Its snaps are A W E S O M E !!!

_________________
-Aaron

cutimages.com
offthewallrc.com
Back to top  
Gezoid



Joined: 24 May 2004
Posts: 161
Location: UK

PostPosted: Sun May 30, 2004 12:04 am    Post subject:  

Anyone tell me WHY you're supposed to lead with elevator first? I seem to snap just fine with everything in at once.
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1177
Location: Sunnyvale, CA

PostPosted: Sun May 30, 2004 6:58 am    Post subject:  

The judges want to see the nose break away from the flight path before the plane rotates. Why exactly, i dunno, but breaking with the elevator is what they do in full scale. I think it gets the plane stalled so that the rudder can throw the tail around easier.
_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 1316
Location: Fremont, CA

PostPosted: Sun May 30, 2004 8:21 am    Post subject:  

Yeah, when I was watching Mark Leesberg do a snap, you can totally see the plane pitches up dramatically before it rotates. He does the best snaps I have ever seen with my own eyes.
_________________
--Meyrick--
Back to top  
Gezoid



Joined: 24 May 2004
Posts: 161
Location: UK

PostPosted: Sun May 30, 2004 9:55 am    Post subject:  

Well yeah, live and learn, eh? I can see your point. Could give some grief on the vertical upline though. Can't wait to get to the field tomorrow and try it out. sly wink
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 1177
Location: Sunnyvale, CA

PostPosted: Sun May 30, 2004 3:26 pm    Post subject:  

Yeah, for the uplines you have to make sure it doesnt break soo far off line that the plane stops, then you have real probs...
_________________
Zak West

www.DesertAircraft.com

www.Smart-Fly.com

www.DarrolCady.com

www.CoolRunningUSA.com

www.TanicPacks.com
Back to top  
3Dfanatic



Joined: 15 Apr 2004
Posts: 300
Location: Tacoma(area), WA

PostPosted: Sun May 30, 2004 9:01 pm    Post subject:  

On Perry's Godfrey, I tune myself into snaps in such a way that there's next to no airspeed when I come out haha. I pull to idle and break at the same time then hit the rud/ail... Looks semi neat.
_________________
-Aaron

cutimages.com
offthewallrc.com
Back to top  
Scott MacAfee



Joined: 24 Apr 2004
Posts: 31

PostPosted: Sun Jun 06, 2004 11:50 am    Post subject:  

Hey recon just fly in sportsman like me and youll get better.
_________________
Scott
Back to top  
3Dfanatic



Joined: 15 Apr 2004
Posts: 300
Location: Tacoma(area), WA

PostPosted: Sun Jun 06, 2004 5:07 pm    Post subject:  

Sportsman's a good place to start. I flew the basic sequence a few times before I really got serious about the whole IMAC thing and it only took me a few times to get bored with it.
_________________
-Aaron

cutimages.com
offthewallrc.com
Back to top  
RightThrust



Joined: 10 Jun 2004
Posts: 4
Location: Ocala, FL

PostPosted: Thu Jun 10, 2004 11:19 am    Post subject:  

Mecam, you mentioned finishing the snap with ailerons. The judges are supposed to deduct for that in the same manner as over-rotations are delt with, 1 point per 10 degrees. "Aileroning" is a way of cheating snaps to make them stop more precise, though it is very obvious when it's done. The best technique, as discussed earlier, is to break the nose with elevator then go straight to the corners and only let off of an input until you let off of everything to stop the snap. This applies in most cases but, say in a negative snap from upright. You have to apply half or so elevator during the first half of the snap then the rest as the plane nears inverted so you can keep the exit on the same line (this type of maneuver is only allowed in unlimited anyways...). A general rule is the most violent break on downlines, moderate on horizontal, and slight on vertical, this seems to work out well.
_________________
Kelly Gerber
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 1314
Location: Fremont, CA

PostPosted: Thu Jun 10, 2004 1:53 pm    Post subject:  

Thanks for the tip RightThrust. I guess every judge have different views on how a snap should look like smile
_________________
--Meyrick--
Back to top  
Motown



Joined: 21 Apr 2004
Posts: 40

PostPosted: Fri Jun 11, 2004 2:01 pm    Post subject:  

I have to agree and dis agree with what right thrust is stating. There is nothing that says that it is leagal or illeagal. The objective is to present a snap to the judges that looks great. When doing a double snap or snaps from different attidudes, you need to lead them and finish them differently so tehy present well. Most of us start snaping our planes by just putting the sticks in the corners and tehn letting off and hoping we don't over or under rotate or loose heading too much. as you progress on through the classes, you learn new tricks to make them present better, by leading with a touch of elevator before putting the sticks in the corners, you show the pitch change and then when the snap comes around, you let off the elevator then the other inputs to come out on the right heading. a lot of the time you will need to release the elevator first or you will come out pitch up or down, that is a deduction. As mecam mentioned, he finishes with aileron input, as long as you don't stop part way through the snap and tehn correct with aileron, it will present better and receive a higher score.
Back to top  
RightThrust



Joined: 10 Jun 2004
Posts: 4
Location: Ocala, FL

PostPosted: Sat Jun 12, 2004 10:33 am    Post subject:  

I see how aileroning out of a snap could look a tiny bit better because you can get a very crisp stop at wings level but technically rolling out with aileron only is not part of the snap as the autorotation stopped before wings were level. We may be thinking of two different things here but I remember seeing some pilot's at imac contest's that will start the autorotation on a 1.5 snap but will let go of everything but aileron for the last 1/2, that definetly doesn't present well and should be downgraded considerably. The autorotation needs to start from wings level and end at wings level in a positive snap for instance.
_________________
Kelly Gerber
Back to top  
C Earnest



Joined: 14 Jun 2004
Posts: 4
Location: Salt Lake City, Utah

PostPosted: Mon Jun 14, 2004 3:40 pm    Post subject: Snaps  

Hi all,

If I may add a little to this string: The purpose behind feeding in elevator first in a snap roll is to lessen the "depth" of the snap. Less airspeed is lost by doing this and you are better set-up to start your next maneuver, especially noticable in up-lines. Activating all surfaces required simultaneously results into a "fully developed" or "deep" snap roll and severly diminishes your airspeed during the maneuver.

Try it both ways and post your results here, please.

Regards,

_________________
Charles Earnest

"Gravity is a harsh Mistress......."

2+2=4. If you don't know this, all is is irrelevant. Albert Einstein
Back to top  
RightThrust



Joined: 10 Jun 2004
Posts: 4
Location: Ocala, FL

PostPosted: Thu Aug 12, 2004 9:11 pm    Post subject:  

No, the purpose of hitting elevator first in a snap is to depart to a stalled flight condition. Which is what a snap roll is, an autorotating displaced roll. If you do not break the snap, it is not a snap and is therefore a zero. The speed at which you enter and exit the maneuver is irrelevant in how the maneuver is judged.

-Kelly

_________________
Kelly Gerber
Back to top  
C Earnest



Joined: 14 Jun 2004
Posts: 4
Location: Salt Lake City, Utah

PostPosted: Fri Aug 13, 2004 5:51 am    Post subject: how...... snaps  

Kelly,

If you are thinking just of the snap maneuver, ok. If you consider the next maneuver and the energy state of the a/c departing the snap, think again. Delaying the other inputs until after the stall is developed results in a higher energy state upon departing the snap maneuver. This results in a smoother transition to the next maneuver and a higher energy state (airspeed) remaining after the snap. Try it.

_________________
Charles Earnest

"Gravity is a harsh Mistress......."

2+2=4. If you don't know this, all is is irrelevant. Albert Einstein
Back to top  
 
   3DBatix Forum Index -> IMAC, Pattern All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive