ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

Rolling harrier help
6 posts
 
   3DBatix Forum Index -> Foamies
 
Author Message
Aubie



Joined: 15 Oct 2004
Posts: 16
Location: Albertville, Al.

PostPosted: Fri Oct 15, 2004 5:50 am    Post subject: Rolling harrier help  

Hi guys, I picked up the e flite ultimate. Castle creations 10 speed control, e flite 370 brushless, 1320 lipo and jr 9303 radio. I have flown it around the yard a few times but didn't really get to wring it out till yesterday afternoon when a flying buddy of mine called me and invited me to the soccer field for a bit of fun. The winds were at times 10 to 12 mph which made for a bit of fun hovering wise. But when they dropped I put the plane through its paces. Harriers, harrier landings and harrier touch and goes were a blast. Rolling circles were easy enough. Still having to dial out the roll coupling on knife edge. Then I wanted to try a rolling harrier. I put it into a harrier started the plane rolling and could get 2 or 3 rolls out of it then would get out of sequence and try to stuff it in the ground. I was usuing aileron and rudder only to attempt this. What is the correct way to do this or am I doing this the correct way and just need a bit more practise with about 12 feet of altitude instead of 4.
Any help greatly appreciated.

_________________
I haven,t failed. I have just found 10,000 ways that won't work. Thomas Edison
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 917
Location: Fremont, CA

PostPosted: Fri Oct 15, 2004 6:18 am    Post subject:  

You can check this training video out. It shows the stick movements in real speed and slow motion. It's done on a G2 simulator but I think it helps.

http://www.3dbatix.com/3dinstvideos.htm

_________________
--Meyrick--
Back to top  
Aubie



Joined: 15 Oct 2004
Posts: 16
Location: Albertville, Al.

PostPosted: Fri Oct 15, 2004 7:26 am    Post subject:  

Thanks for the info Meyrick. I'll give it a shot the next time I take the ultimate out.

Another question. How easy is it going to be to transfer per say the 3d stuff that I am learning with the foamie over to a glow plane then a 33% plane. Long story short I quit flying a bout a year and a half ago due to health problems. The ultimate is the first plane I have gotten behind the sticks of since then. I feel very comfortable with the foamie. The thought is fly the foamie through the winter then go for a u can do 60 size this spring, get to where I can do the same things with it as the foamie then mid summer go to a gasser. Am I thinking correctly on this?

_________________
I haven,t failed. I have just found 10,000 ways that won't work. Thomas Edison
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 917
Location: Fremont, CA

PostPosted: Fri Oct 15, 2004 8:05 am    Post subject:  

Aubie wrote:
Thanks for the info Meyrick. I'll give it a shot the next time I take the ultimate out.

Another question. How easy is it going to be to transfer per say the 3d stuff that I am learning with the foamie over to a glow plane then a 33% plane. Long story short I quit flying a bout a year and a half ago due to health problems. The ultimate is the first plane I have gotten behind the sticks of since then. I feel very comfortable with the foamie. The thought is fly the foamie through the winter then go for a u can do 60 size this spring, get to where I can do the same things with it as the foamie then mid summer go to a gasser. Am I thinking correctly on this?


You will be much better.. My rolling harriers were a lot better on my gasser and I felt more confident after flying them on my foamies. I also know a lot of people practiced torq rolling on foamies and were able to do em on their gassers with ease in short term. Foamies are your best 3D training tool without a doubt.

_________________
--Meyrick--
Back to top  
Aubie



Joined: 15 Oct 2004
Posts: 16
Location: Albertville, Al.

PostPosted: Sun Oct 17, 2004 7:59 pm    Post subject:  

Thanks again for the info Meyrick it made a diffrence. A friend of mine called yesterday to do a little flying at the soccer field. We both flew about 10 minutes hovering one plane ver close to the other which was awsome but then Bob wanted me to show him how to do a rolling circle. He is an accomplished pattern competitor but has never really tried any of the 3d stuff. I had been working on the rolling harrier earlier at our local flying field earlier and was starting to get the feel of doing one so I figured do a couple of slow rolling circles to let him see what the plane was doing and what the stick movements were then go into a rolling harrier to show off a little bit. A gentle toss and the little ultimate was at about 8 feet high doing a rolling circle. On the second pass I quickened the speed of the roll and when the plane was pointed into the wind I went from rolling circle into rolling harrier. My cadance on the sticks was rite in time. So I decided to drop the altitude to about 3 feet off of the deck and had the biggest grin you could ever imagine. Then I got a glitch, not a radio glitch but a glitch between my brain and my thumbs. It was at that point the ultimate decided to take a dirt nap. We both walked over laughing about what had just happened. The front of the fuse is split in three places all the way back to the rear of the cabane and the top wing was half torn of off.
We were both still laughing about the carnage and then Bob made the statement about flying three mistakes high not three feet when learning new manuvers. Ironically a few minutes later Bob was getting the hang of a rolling circle and rolled his plane into rite into the ground from about the same heigth that I was on the rolling harrier.
Both planes are repaired and ready to fly again. We plan on another flying venture wednesday. We just have to remember three mistakes high, not three feet.

_________________
I haven,t failed. I have just found 10,000 ways that won't work. Thomas Edison
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 917
Location: Fremont, CA

PostPosted: Sun Oct 17, 2004 8:29 pm    Post subject:  

That's the best thing about foamies, you crash em, you CA em and you're off to 3Ding again in a couple of minutes. Glad you're having fun with these things.
_________________
--Meyrick--
Back to top  
 
   3DBatix Forum Index -> Foamies All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive