ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

3D Maneuvers for CAP!
13 posts
 
   3DBatix Forum Index -> 3D Talk
 
Author Message
TeamMoki3D



Joined: 08 Oct 2004
Posts: 161
Location: Belvidere, NJ

PostPosted: Fri Oct 08, 2004 6:15 pm    Post subject: 3D Maneuvers for CAP!  

Anyone know a good 3d maneuver that a cap(15 lbs) with a Moki 2.10 can do?? Have any good tips Zak?

its the hangar 9 1/4 scale one

i can hover it but i have no pictures..

hey Zak,would you happen to know why my moki seized up on me after the first flight? and as you know, a cap has two large holes in the cowl, plenty of cooling. gerard thinks there may be a problem with the pipe extensions at the bottom of the cowl, what do you think?

_________________
-Saucy-
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 582
Location: Sunnyvale, CA

PostPosted: Fri Oct 08, 2004 6:18 pm    Post subject:  

It seized? Thats insane, but you say it did, then wow. There are a few things that could have happened. Prop too big, too high nitro, or not cool enough. One thing to do to increase the cooling from the cowl is to build a lip on the bottom of the cowl to create a negative pressure (vacuum) to suck exhaust air out. (Ill get a picutre of this in my next post here).

Caps are great at things like Waterfalls and Lamcevaks. But if its set up for 3D, it should do anything with a little work. Harriers, blenders, rolling harriers, high alpha knife edge. There are very few "known" 3D maneuvers, it just depends on how you put them all together.

_________________
Zak West
Team DA

Desert Aircraft

Smart Fly

Fromeco Avionics

Stick and Rudder Photos
Back to top  
TeamMoki3D



Joined: 08 Oct 2004
Posts: 161
Location: Belvidere, NJ

PostPosted: Fri Oct 08, 2004 6:49 pm    Post subject:  

yeah, thanks for the advice, well i have a new moki 2.10 ready to go in the big cap now, i added lots of cooling holes and made those lips you said. I just got this plane and im a little excited to get it back in the air. im only 12 so i am practicin on this cap for competition. Thanks for the professional advice agen Zak!
_________________
-Saucy-
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 582
Location: Sunnyvale, CA

PostPosted: Fri Oct 08, 2004 6:50 pm    Post subject:  

Here is the lip that will create a vacuum on the bottom of the cowl.


PA080227.JPG
 Description:
 Filesize:  40.59 KB
 Viewed:  159 Time(s)

PA080227.JPG



_________________
Zak West
Team DA

Desert Aircraft

Smart Fly

Fromeco Avionics

Stick and Rudder Photos
Back to top  
TeamMoki3D



Joined: 08 Oct 2004
Posts: 161
Location: Belvidere, NJ

PostPosted: Fri Oct 08, 2004 6:55 pm    Post subject:  

hey, thanks man! this should work great, since the fuel doesnt include any nitro in it at all, im using S&W "moki" fuel. My friend Matt has a BGX in his ultimate, his engine is barely cooled and hes using the same fuel as me, is the BGX a better motor than the Moki? oh yeah, one more thing. im leaning towards a DP 330l, would a 2.10 be good in that?
_________________
-Saucy-
Back to top  
TeamMoki3D



Joined: 08 Oct 2004
Posts: 161
Location: Belvidere, NJ

PostPosted: Fri Oct 08, 2004 6:57 pm    Post subject:  

o yeah, about that lumcevak. thats basically a few inside snaps at the top of a verticle right?
_________________
-Saucy-
Back to top  
3dbatixkid
Moderator


Joined: 15 Apr 2004
Posts: 582
Location: Sunnyvale, CA

PostPosted: Fri Oct 08, 2004 7:21 pm    Post subject:  

No, roll left, add in right rudder, and full down. The plane should go end over end, rotating about the CG and flying totally sideways.
_________________
Zak West
Team DA

Desert Aircraft

Smart Fly

Fromeco Avionics

Stick and Rudder Photos
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 624
Location: Fremont, CA

PostPosted: Fri Oct 08, 2004 7:45 pm    Post subject:  

Also, make sure you're using a large enough fuel line, at least 1/8" ID. I was using 5/32 ID on my Moki 1.8 and boy does she idle low... Very Happy
_________________
--Meyrick--
Back to top  
TeamMoki3D



Joined: 08 Oct 2004
Posts: 161
Location: Belvidere, NJ

PostPosted: Sat Oct 09, 2004 7:42 am    Post subject:  

hey what plane do you have your 1.8 in?
_________________
-Saucy-
Back to top  
Meyrick
Site Admin


Joined: 15 Apr 2004
Posts: 624
Location: Fremont, CA

PostPosted: Sat Oct 09, 2004 8:02 am    Post subject:  

TeamMoki3D wrote:
hey what plane do you have your 1.8 in?


You want to use the 1/8 ID on any motor that is .90 and up. I had the H9 Edge 540 with a Moki 1.8. I also use 1/8 ID tygon on my 100cc gasser.

_________________
--Meyrick--
Back to top  
TeamMoki3D



Joined: 08 Oct 2004
Posts: 161
Location: Belvidere, NJ

PostPosted: Sat Oct 09, 2004 6:12 pm    Post subject:  

yeah i have 1/8 ID on my moki
_________________
-Saucy-
Back to top  
TeamMoki3D



Joined: 08 Oct 2004
Posts: 161
Location: Belvidere, NJ

PostPosted: Sat Oct 09, 2004 6:16 pm    Post subject:  

hey meyrick or zak, what motor do you think a good motor for my ucd? its the 46 size, i want to get used to torqing at low altitudes. do you think the saito 82 would be enough or no?
_________________
-Saucy-
Back to top  
3Dfanatic



Joined: 15 Apr 2004
Posts: 264
Location: Tacoma(area), WA

PostPosted: Sat Oct 09, 2004 6:41 pm    Post subject:  

Yea, back to the cooling thing. You can have all the air in the world goin in, but if none comes back out, it's futile. For every square inch of intake you should have 2-3 exit.
_________________
-Aaron

cutimages.com
offthewallrc.com
Back to top  
 
   3DBatix Forum Index -> 3D Talk All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive