 |
 |
| |
| Author |
Message |
DTB

Joined: 24 Jul 2004 Posts: 116 Location: Jackson, MS
|
Posted: Thu Sep 16, 2004 3:41 am Post subject: Funtana 90 maiden flight |
|
|
Hi everyone, I was able to do a maiden flight on Sunday. This thing is Funtastic. I did have a slight mishap. It is funny now, but not when it happened. I had everything set and secure or at least I thought. I took off and flying level while shaking like a nervous wreck due to all the stories of exploding wing on take off. I was flying around and did a roll and flying around and saw something move. I looked closer and notice that my main landing gear had turned 90 degress. I said "OH CRAP!!!". I did a low slow fly by to get a closer look and sure enough, the landing gear was parallel with the fuse directly under it. I thought, "OK, how can I handle this situation, then some members started yelling, don't land, stay up, then I thought, Put the plane into a hover to keep in over the in field and let the gear vibrate off and sure enough it worked. The gear fell off and I was happy like a fat kid with cake. I brought the plane in for it's very first landing. Landing with no gear to top it off. I brought it in low and slow and about 1.5 feet off the ground (grass section), I cut the motor and let it belly land. The only damage was to the sullivan Tail wheel, which was fixed at the field. The gear fell out and the screw landed inches from the gear and again could see there was no loctite on the screw. I thought about it, Arrrrrrrrrr I never did tighten up the gear or loctite the gear on. That was totally my fault and luckily I didn't tear up anything. I was so busy making sure everything else was secure, I didn't even think about the gear since I had put it on in the beginning of the build and never got back to it. How dumb is that? Oh, well. Lesson learned.
The YS 1.10FZ is amasing on this plane. Vertical pull out is unbelievable. This motor is still breaking in and running a little rich and is spinning an APC 16x4W at 10,300. I definately can go to a 17x4 with no problem. I can't get over how strong this motor is. My YS .91FZ looks exactly like this motor, but can't touch it in power. WOW!!!!!!
I guess, after my situation just make sure that your landing gear is secure. Now it has a lock washer and loctite. Doing much better now.
Hope to get some more flying in once Hurricane Ivan has left the area.
DTB
| Description: |
|
| Filesize: |
90.09 KB |
| Viewed: |
329 Time(s) |

|
_________________ Fly it hard and hover it low...
My RC Photo Page |
|
| Back to top |
|
 |
Shaun

Joined: 10 Sep 2004 Posts: 185 Location: texas
|
Posted: Thu Sep 16, 2004 6:34 am Post subject: |
|
|
Glad everything turned out ok for you Derrick!
That would bite to have the landing gear leave on the first flight
I am just starting to put my funtana together.
What did you put your cg at for the first flight?
thx
Shaun
|
|
| Back to top |
|
 |
3dbatixkid Moderator

Joined: 15 Apr 2004 Posts: 581 Location: Sunnyvale, CA
|
|
| Back to top |
|
 |
DTB

Joined: 24 Jul 2004 Posts: 116 Location: Jackson, MS
|
Posted: Thu Sep 16, 2004 9:54 am Post subject: |
|
|
| Shaun wrote: | Glad everything turned out ok for you Derrick!
That would bite to have the landing gear leave on the first flight
I am just starting to put my funtana together.
What did you put your cg at for the first flight?
thx
Shaun |
Thanks Shaun, what setup are you going with on your Funtana?
I actually took photos of the complete assembly and planned on putting a little web page together to document what I had done. Robart hinges, dual taill wire brace, Robart Hinges, Sullivan Tail wheel assembly, etc... If you like, I can put it together and post it for you. It may help some out with their build.
I started out with my CG at 6-7/8" and will fly it there a little more to get the feel for the plane a little more. Great location to start. As you can see, I was hovering on the first flight. By force not choice. I like to get everything trimmed out first. I was doing harriers, blender, waterfalls, etc.. on the second flight, then for some strange reason I lost my tail wheel so that was all the flying I did that day because I did'nt have a spare wheel. All three wheels came off that day. HAHA, LOL... I like a sort of tail heavy plane, but will fly it here for a while then will move back as needed.
| 3dbatixkid wrote: |
DTB, i had the same thing happen on my F40. Instead of gettin the gear to fall off, i brought it into a hover right infront of me, and made Steve go catch it. |
I do this is an easy item to over look if you are not careful.
_________________ Fly it hard and hover it low...
My RC Photo Page |
|
| Back to top |
|
 |
Shaun

Joined: 10 Sep 2004 Posts: 185 Location: texas
|
Posted: Thu Sep 16, 2004 11:32 am Post subject: |
|
|
I'm not getting to tricky. This will be my first 3-d plane. I'm building it pretty much stock.
I have put a saito 100 in it, and today I just put the Hitec hs635hb servos in.
I took the day off so well see what I can get done while I have the time .
I might change some stuff later on after I see where the cg lands up?
I just want something not to tail heavy at first
|
|
| Back to top |
|
 |
Radioflyer

Joined: 14 Sep 2004 Posts: 92 Location: Kalamazoo, MI
|
Posted: Fri Sep 17, 2004 6:52 pm Post subject: |
|
|
DTB
It happens all the time. All these things to do 'till it's in the air, so little time, and sometimes attention to detail is left out. We've all done it. What a blessing that it was just your gear not an evavator servo horn missing a screw, or a servo conection to your equipment causing you to loose control. I've heard alot of stories lately of oversights(Which Happen!) that can cause major problems. It's always good to take the windy, crappy days to look over all of your stuff and make sure it's gonna be safe when it gets up in the air.
Great looking plane cradle! Keep the dirt off the prop!
|
|
| Back to top |
|
 |
DTB

Joined: 24 Jul 2004 Posts: 116 Location: Jackson, MS
|
Posted: Sat Sep 18, 2004 8:17 am Post subject: |
|
|
| Radioflyer wrote: | DTB
It happens all the time. All these things to do 'till it's in the air, so little time, and sometimes attention to detail is left out. We've all done it. What a blessing that it was just your gear not an evavator servo horn missing a screw, or a servo conection to your equipment causing you to loose control. I've heard alot of stories lately of oversights(Which Happen!) that can cause major problems. It's always good to take the windy, crappy days to look over all of your stuff and make sure it's gonna be safe when it gets up in the air.
Great looking plane cradle! Keep the dirt off the prop! |
Good advice about the crappy windy days. I flew again yesterday. Got a couple of flights on it now. I had a Sullivan tail wheel, but it kept twisting and buckling even on good landings which would limit the amount time I could fly, so I replaced it now with another type that seems much better.
| Description: |
|
| Filesize: |
86.6 KB |
| Viewed: |
223 Time(s) |

|
_________________ Fly it hard and hover it low...
My RC Photo Page
Last edited by DTB on Sat Sep 18, 2004 8:42 am; edited 1 time in total |
|
| Back to top |
|
 |
DTB

Joined: 24 Jul 2004 Posts: 116 Location: Jackson, MS
|
Posted: Sat Sep 18, 2004 8:23 am Post subject: |
|
|
Another view.
I flew my Funtana S 90 again yesterday. Got a couple flights on it now. I had a Sullivan tail wheel, but it kept twisting and buckling even on good landings which would limit the amount of time I could fly, so I replaced it now with another type that seems much better. I flew yesterday doing flat spins (upright and inverted), blenders, knife edges, walls, waterfalls, harriers, hovering, torque rolls, rolling circles, rolls, etc... I am still getting everything set as for as expo and spoilerons rates, etc... This plane is very fun. I can't wait to get some more time on it. Again if you are at sea level, the YS 1.10FZ is all that is needed. Vertical performance is very good. The APC 16x4 is spinning constantly at 10,300 on the ground. I need a APC 16x6 or 17x4 to get the rpm down some. I can't imagine what 30% would fly like.
Specs:
YS 1.10FZ
Wildcat 20/20
(5) HS-5645MG on control surfaces
(1) HS-85BB on throttle
Robart hinges
Robart 1" Control horns
1" servo arms
Hitec Super Slim 8-channel Rx
Futaba 9C Tx
1650 NiMH 6V
Dual Wire Tail Brace
Great Plane Tail Wheel
20oz Tank
APC 16x4 prop (need a APC 16x6 or 17x4)
2.5" Tru-Turn Spinner
PSP Spinner adapter
PSP Fuel Dots
Beafed up wing
Charging jack
Black Nylon wing bolts
Clipped in wing
Blocked wheel pants
| Description: |
|
| Filesize: |
119.43 KB |
| Viewed: |
222 Time(s) |

|
_________________ Fly it hard and hover it low...
My RC Photo Page |
|
| Back to top |
|
 |
Radioflyer

Joined: 14 Sep 2004 Posts: 92 Location: Kalamazoo, MI
|
Posted: Sat Sep 18, 2004 6:35 pm Post subject: |
|
|
DTB
Hey, I heard that some of the 90 size funtanas ( as well as many of the Horizon
aircraft ) have weak wing sturctures. Problems like crushed ribs where the wing tube sits and all out wing failures have happened durring high G's and
prolonged use. Just something you may what to keep an eye on. Enjoy
Keep that dirt off the prop
|
|
| Back to top |
|
 |
DTB

Joined: 24 Jul 2004 Posts: 116 Location: Jackson, MS
|
Posted: Sat Sep 18, 2004 7:13 pm Post subject: |
|
|
| Radioflyer wrote: | DTB
Hey, I heard that some of the 90 size funtanas ( as well as many of the Horizon
aircraft ) have weak wing sturctures. Problems like crushed ribs where the wing tube sits and all out wing failures have happened durring high G's and
prolonged use. Just something you may what to keep an eye on. Enjoy
Keep that dirt off the prop  |
Thanks for the advice Radioflyer, I have heard about the wing failures. There is a huge thread I participate in on another forum about this plane. Many have had problems due to wing failures. I did check my wing and had a few cracked ribs. I CA'd the ribs, wing tube area, sheer web, servo tray, leading edge and trailing edge. I also brushed thinned epoxy on all the ribs in the wing also. I have flown mine a couple of times doing blenders, flat spins, rolls, walls, inverted walls, etc... I hope that my mods will keep the wings together. I have a 1:1 Mechanical Advantage also on the servos also. HS-5645MG digitals used also. The manual states 50oz servos minimum and 82oz optimum. My digitals have 168oz of torque. The surfaces are sealed on the top and bottom also. I do think that the crack ribs could have contributed to some of the failures, but some I think are flying maybe too fast also. We'll never know that answer.
_________________ Fly it hard and hover it low...
My RC Photo Page |
|
| Back to top |
|
 |
| |
Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group
blueGray theme by Nuttzy
|