ARCHIVED FORUM (READ-ONLY)  ·  about this archive
3DBatix Forum Index

extra 330 3d building advice
4 posts
 
   3DBatix Forum Index -> Foamies
 
Author Message
nitro2



Joined: 08 Apr 2008
Posts: 2

PostPosted: Tue Apr 08, 2008 9:18 am    Post subject: extra 330 3d building advice  

Hi forum ,

Being a returner ( last plane gone about 30 years ago ) to plane flying , a have several questions....................... :oops:

I am considering building a depron Extra 330 3d but ,

Who can give me some advice on the following;

-- Can the whole plane be build from 6 mm depron ??

-- How important is the weight of the single items , why ..................well i have several heli pieces around which could be used on this plane , the problem is they are slightly heavier than what is mentioned in the building advice........ ( servo ok , rcv ok , esc 40 gram , lipo 100 gram )

-- What alternatives are there to the brushless, i have a 1000/v outrunner can this one be used ???

-- Will it be possible to use 11,1 v 2200 lipo or will i run into weight problems then...........

All help hihgly appreciated.



nitro2
Back to top  
steven460



Joined: 06 Apr 2008
Posts: 3

PostPosted: Tue Apr 08, 2008 10:33 am    Post subject: Re: extra 330 3d building advice  

Hello
(this being my 2nd post) but i dont want to call my self an aircraft building novice (build some odd models like the hydrofoam, pibros, avanger and custom flying wings)

From what I have noticed with buildin the Diablo foamy, is that the weight does matter but not as bad compared to with other models.
Ive build the the Diablo from 3mm sheets, sandwiched them.. that TWICE the cutting work, and glued it all with Poly-Urethane foaming glue. Also known as gorilla Glue. Its brown/Yellow and extracts watervapour from the air to solidfy.

My gear :
- HiModel 1400rpm/V outrunner, (29 grams excluding mounts and prop saver)
- 11A Pulso ESC (6 grams, its also sold as a 12A HiModel, identical pink :oops: wires)
- 1000mA 11.1V 20C Lipo, which comes at 99 grams + plug
- 3x 8 grams analog elchepo servo's their quite fast and strong and dont jitter at all.
- Master Synthersizer receiver (5 grams)

total gear = 175 ish grams including the prop. (im using a 8x4 up to 8.5x4.5 which gives stupidly amounts of thrusts in expensive flytime)
the body and gear is about 320 grams or 12oz. 12 oz is slightly too light, this is partly due to the small motor, a 50 grams motor would have been better as ive added a 20 grams weight to the nose to get close to the suggested CG on the drawings.

Hope i've helpen :roll:

//Greets
Steven from NL
Back to top  
nitro2



Joined: 08 Apr 2008
Posts: 2

PostPosted: Tue Apr 08, 2008 11:26 am    Post subject: Re: extra 330 3d building advice  

Yep ,

all info is valuable .

So , the weight of the parts must be kept in mind ;

rcv is a 6 ch ,at 8 gr ( crystal ??? )
lipo at 100 should be okay ,
servo's at 8 gr /pc must be okay,
esc 30 A around 26 gr,
motor 1000/v around 59 grams
prop and mounting ????

so maybe on the higher side .

i wonder if someone has been using another motor as the axi2212/34 or himax 2812-0850 , these are quite expensive and around 900/v


any additional info is welcome.


nitro2
Back to top  
steven460



Joined: 06 Apr 2008
Posts: 3

PostPosted: Tue Apr 08, 2008 12:43 pm    Post subject: Re: extra 330 3d building advice  

For teh motor part
it has to give about 500 to 600 grams static

Thats about 20oz thrust... In other words, the motor has to push the plane's weight + the planes weight :D well almost.
From what I understand thats 3D flying.

Im using a 14 euro motor, and im happy with it, its a 1400rpm/v @ 8x4 or 8.5 x 4.5 its fine.
HiModel 2208/14 cheap! using that small esc works fine
Back to top  
 
   3DBatix Forum Index -> Foamies All times are GMT - 8 Hours

Powered by phpBB 2.0.6 © 2001, 2002 phpBB Group

blueGray theme by Nuttzy
Restored from the Internet Archive, 2026 · about this archive